There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
French cleats are a simple way to hang things on walls while allowing easy repositioning. One bevelled cleat is fastened to the wall and the other is fastened to whatever you want to hang. One catches the other and gravity does the rest. French cleats are commonly cut at 45 degrees but I prefer to cut mine at around 30 degrees. This makes them easier to lift off the wall (especially way up high) without sacrificing security.
Although refrigerators long ago rendered them obsolete, antique oak ice boxes remain popular with collectors, even though they’re expensive and hard to find. This do-it-yourself version is neither: it’s both inexpensive and easy to build. An authentic reproduction of an original, the project is especially popular when used as a bar, but it has many
And this is the front side which is where I primarily stand when using the table. The top surface has 3/4” holes on 4” centers to allow clamping material pretty much anywhere on the table. It also features a hollow torsion box design for added stiffness to the top surface and empty space just below the work surface to place hand tools out of the way when working on something.
Drill four 5/8-in.-dia. 1/2-in.-deep holes on the large disc?inside the traced circle?then use 5/8-in. dowel centers to transfer the hole locations to the underside of the small disc. Drill four 1/2-in.-deep holes on the underside of the small disc and a 1/2-in.-deep hole in the center of the top for the dowel handle. Glue in the dowels to join the discs, and glue in the handle. We drilled a wood ball for a handle knob, but a screw-on ceramic knob also provides a comfortable, attractive grip.
There’s nine more drawers that I didn’t take interior pictures of because it’s just generic stuff. But I will go through the contents for you. Top to bottom in the left column is a drawer for manuals, a drawer for every letter that I have received from all of you out there, and a drawer for my electrical tools and supplies. Top to bottom in the center column is a drawer for miscellaneous hand tools that are more general household and carpentry related such as pry bars, putty knives, and drywall tools, a drawer for hammers, mallets and squares, and a drawer for all of my hand held cutting tools like handsaws, knives, and chisels. Top to bottom in the third column is a drawer for all types of brushes, a drawer for all of my sanding tools and supplies, and a drawer for all of my router bits and attachments.
The table saw is always connected to my dust collector with a couple pieces of 4” flex hose and some 4” sewer and drain PVC pipe and a homemade blast gate. The port on the table saw is at the rear of the cabinet and this particular area of the shop sees the least amount of foot traffic so I have no problem just leaving the ducting on the floor. I also always have a few other cords on the floor here. I see this as the same principle as walking onto a porch. You know the steps are there so you pick up your feet. I know the pipe is there so I pick up my feet. Not a trip hazard in my opinion.
In my machine shop, I store my thickness planer under the infeed table of my jointer. The feed direction of the planer is one direction and the jointer the other. This works especially well because I can joint all my boards and stack them on a cart or sawhorses; then, without reorienting them, I can feed them through the planer (after I pull it out, of course).
Start with ¾" plywood that is twice as wide as the depth of the cabinet and as long as one side and top/bottom. I crosscut the top and bottom off of one end and set it aside. Then, using a ½" dado stack in my table saw, I cut a series of ¼" deep dadoes across the sides. Make the spacing between them uniform so that the drawers are interchangeable. Finally, rip the sides and top/bottom in half to separate them and assemble the cabinet however you please. If you want to hang it on a wall, attach a French cleat to the back at the top and a batten of equal thickness at the bottom.
Drawers are really useful in a wood shop – you can’t have enough. They keep out the dust and with dividers or compartments they can help organize as well. A drawer that is too deep ends up getting filled with anything that fits and becomes a junk drawer, so multiple shallow drawers are better than one deep drawer. However, drawer slides can be expensive so I make my own drawers with built-in drawer slides. In addition to saving costs, if I make multiple cabinets the same width, I can move drawers from one cabinet to another quickly and easily.
The next vertical tool is my 13” benchtop drill press. It’s a cheap Harbor Freight model that isn’t perfect but isn’t a bad buy either. It has several flaws that I would consider “areas for improvement” and not problems. I would purchase this again if I had to do it over. I have a larger drill pres table with integrated storage drawers for it but find it to be a little too big for where I currently have the drill press in the shop.
You can also use Google image search to research a project. Unlike the PDF search, the image search provides a photo of what the project will look like, which is helpful in determining if you want to pursue building it. By doing an image search for how to build a step stool, you will have a ton of options that all lead to woodworking plans of various quality. (The how to part of these is important—otherwise you’ll just get pictures of step stools.)