Below the top structure I mounted a long power outlet bar to have a convenient power location for whatever corded tool I am using at the table. Below that is the lower shelf which I built specifically to house my X-Carve CNC machine. This machine has 1000mm rails so making a dedicated cart for it would take up quite a bit of valuable floor space. The idea behind storing it on this shelf was so that I could easily slide it off and place it on the top work surface to use it. However, I haven’t actually removed it from it’s current location yet. I can use it where it is with no problems.
As soon as I came across this tutorial, I didn’t wait any longer to start building one. Some of the items you need for this project are hardwood plywood, saw, glue, nails, drilling machine, etc. The video is very easy to follow for anyone with basic woodworking knowledge and experience. The first source link also includes a step by step procedure in plain English for those, who are not comfortable enough with the video tutorial.
My shop is about 425 square feet, roughly the size of a two-car garage. However, there is a wall running down the middle with a sliding glass door at one end that reduces the openness. It also increases my wall space. Plus, I have all my machinery on one side of the wall, so all the dust and noise stays out of the bench room. In this article, I want to share with you some of the things that make my shop such a nice place to practice my craft and give you ideas of how to make the most of the space you have.
Why would you buy a costly platform bed from Ikea or somewhere else when you can make one yourself at home? Oh yes, you can. A bed is the most common furniture piece used in the house and probably the costliest one. Wouldn’t it be great if you could just make a bed of your own, without having to spend many bucks for buying one? So I am here sharing a great tutorial to help you to build a nice comfy platform bed that you can use anywhere in the house.
It’s been a solid year since moving into this house and starting my shop. Nearly everything in my shop is on casters for mobility. In my opinion the most important tool in any woodshop is the table saw so lets start there. My table saw is a SawStop PCS with 52” rip capacity. The attention to detail on this machine is phenomenal. I have the industrial mobile base for it which makes the single heaviest item in my shop one of the easiest to move. The base lifts the entire saw, including the extension wing, several inches with ease. It is actually in the up position in the following image. I also spray painted the location of the extension wing supports on the ground so I can easily locate a familiar position when setting up the saw. Because moving it around the shop on the mobile base is effortless I find myself moving it out of the way frequently when I know I’m not going to be using it for a while. I also keep a couple trash cans near the table saw.
French cleats are a simple way to hang things on walls while allowing easy repositioning. One bevelled cleat is fastened to the wall and the other is fastened to whatever you want to hang. One catches the other and gravity does the rest. French cleats are commonly cut at 45 degrees but I prefer to cut mine at around 30 degrees. This makes them easier to lift off the wall (especially way up high) without sacrificing security.
Spanning 14-1/2′ of the back wall is my miter saw station. Completing this has resulted in a huge increase in storage space, organization, and convenience when using the miter saw. It features 20 drawers and a pull out tray for storing my planer out of the way. Eight upper storage bins are for commonly used items such as my cordless tools as well as other items that don’t need to be stored away from dust. There is integrated dust collection for the miter saw and a stop block to the left of the saw with roughly 106” of capacity.
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
Here’s a traditional Swedish farm accessory for gunk-laden soles. The dimensions are not critical, but be sure the edges of the slats are fairly sharp?they’re what makes the boot scraper work. Cut slats to length, then cut triangular openings on the side of a pair of 2x2s. A radial arm saw works well for this, but a table saw or band saw will also make the cut. Trim the 2x2s to length, predrill, and use galvanized screws to attach the slats from underneath. If you prefer a boot cleaner that has brushes, check out this clever project.
Hey, I want to build all of these (and I did read to the end), but my list of projects is so long that any one of these will have to wait ’til next year (and i don’t mean January). thanks for all these ideas. there is one more i read about in the Handy Family Man. It is an adaptation to your shop vac that puts the hose at your project so it sucks up the dust as it is produced. Wonderful, right? Maybe next year!
An excellent introduction to woodworking is to use crates as your main material. The boxes are already formed, which means less assembly work for you—yet it looks impressive once your project is altogether. With this crate coffee table, you still get to practice your skills adding the casters and the center box. Finish with a little stain, and this table is ready to roll. You can find the full tutorial at DIY Vintage Chic.
Plywood and long stock can also be a challenge to store in a shop. When I had an 8' bank of cabinets in my shop, I used to slide my sheet goods in behind it. Now that they are gone, I just stand them up against the wall and use a wedge system to keep them neat and upright. Long, narrow material goes on my lumber rack beside my table saw. I also store dry lumber standing on end in one corner of my bench room.
Do you want to use an oil stain, a gel stain, a water-based stain or a lacquer stain? What about color? Our ebook tells you what you really need to know about the chemistry behind each wood stain, and what to expect when you brush, wipe or spray it on. It’s a lot simpler than you think! This is the comprehensive guide to all the varieties of stain you will find at the store and how to use them.