In my machine shop, I store my thickness planer under the infeed table of my jointer. The feed direction of the planer is one direction and the jointer the other. This works especially well because I can joint all my boards and stack them on a cart or sawhorses; then, without reorienting them, I can feed them through the planer (after I pull it out, of course).
This is not exactly a tutorial, but a guide to some really cool woodworking projects. Although we are not teaching you to make anything, we are always here to help. Feel free to ask your queries in the comments in case if you face any issue while working on any of these projects. Also, tell us how much you liked this article. Did you enjoy reading it? Did you work on any of these projects, and if yes, how was your experience? You are also welcome to share any images of your completed woodwork projects.
The final corner of my shop houses my Grizzly G0703P mobile dust collector. I upgraded to this unit shortly after setting up this shop as my last dust collector was setup to exhaust air outside. The separator I made for it wasn’t efficient enough to modify again for a canister filter for exhausting air inside the shop. I really didn’t want to deal with modifying my dust collector again so I got this. Above the dust collector is my retractable air hose reel that I mentioned earlier. I like having this here as the only times I use compressed air is to fill up the my vehicle tires or to spray a finish which I do outside.
I really enjoyed this video. I don’t particularly enjoy watching videos every time someone changes the layout of their shop. But, yours is the exception. I know a lot of your fans have probably been asking for a while for you to do a tour of your shop. Glad you waited till it was all finished to do it. You must’ve shot this video before you got your festool tools.
Slice, dice and serve in style on this easy, attractive board. We’ll show you a simple way to dry-fit the parts, scribe the arc and then glue the whole thing together. We used a 4-ft. steel ruler to scribe the arcs, but a yardstick or any thin board would also work. Find complete how-to instructions on this woodworking crafts project here. Also, be sure to use water-resistant wood glue and keep your board out of the dishwasher or it might fall apart. And one more thing: Keep the boards as even as possible during glue-up to minimize sanding later. For great tips on gluing wood, check out this collection.
Right in front of my finishing supply rack is my welder and welder cabinet. It’s a Hobart Handler 140 mig or flux core wire feed welder. I learned how to weld several years ago on an old manual adjustment arc welder and I very much like the convenience of the wire feed in this one. It’s sitting on a Harbor Freight welding cabinet. I have only used it in one video so far (metal vise build) but have used it a few times since then on stuff around the house. Having a welder isn’t a necessity but it is very convenient at times.
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!
Have you got an old whiskey barrel at home that you haven’t used for ages? If yes, this project is for you. You can make a really beautiful coffee table from that old whiskey barrel in a few easy steps. Apart from a coffee table, whiskey barrels can also be used to build several other furniture items. But that is a talk for later. Here, we will discuss how to make a coffee table from a whiskey barrel.
As with most websites, we do log web visits. This information, however, does not have a link to you personally. These logs help us understand the needs of our audience and the areas of our site that you do or do not find useful. When you simply browse our site, no personal information is being collected. We may disclose this non-personal information to third parties such as sponsors, clients or advertisers.
My shop is about 425 square feet, roughly the size of a two-car garage. However, there is a wall running down the middle with a sliding glass door at one end that reduces the openness. It also increases my wall space. Plus, I have all my machinery on one side of the wall, so all the dust and noise stays out of the bench room. In this article, I want to share with you some of the things that make my shop such a nice place to practice my craft and give you ideas of how to make the most of the space you have.
Google is probably the first place where most people would start searching for woodworking plans, but often the top results can be a mix of articles and how-to pieces that just aren’t detailed enough. Sometimes they’ll link to the plans (like we try to here at Lifehacker), but other times, they’re just showing off a cool project. There are better, more precise ways of finding what you’re looking for.