Learning from the ideas of other woodworkers, while avoiding their mistakes is an excellent way to design and set-up your own shop layout. Setting up a woodworking shop as a hobby place, or for a some one more serious, who even may venture off into some sort of woodworking business; is not as easy as it might sound. Knowing the correct steps to follow will save you time and money, but it will also save you a lot of stress down the road.
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
Yes, another website with a simple design. However, they are high in content and offer great woodworking plans for a whole range of interesting and easy to do projects. iBuiltIt.ca has been around for a while, and is a well-respected online real-estate, mostly because of their quality plans. Their plans are ideal for both beginners and experts alike.
If you bought this superb polished table in a store, it would cost you a fortune, but our detailed instructions will help you make one for less than $100. And it looks like highly polished stone, but no-one would know it’s actually made from concrete with a wooden base. Also, you can embellish the top with leaf prints, like the table shown here, or personalize it with glass or mosaic tiles or imprints of seashells.

With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
Turning an old door into a photo frame is another easy woodwork project. All you need is an old door and some woodworking tools and items. I am here sharing the link to the source tutorial that explains the step by step procedure for building a picture frame from an old wooden door. This tutorial was originally written by Tracy Snyder at athomewithsweett.blogspot.com who also tells you what items you may need and where to find them. If you haven’t already got an old door, you can purchase one from websites like Craigslist.
Jay, You gave some vital advise- not to go into debt over a tool. Unfortunately I do owe a little for some of my things about $300.00 worth, but I went from $60,000/year income down to $25,000/year when I retired due to bone CA I had as a teen.( I was only suppose to live 3 month and I am now 54, so guess they were wrong about that.) But with age comes arthritis in the arek9a of surgery and was force to give up my job as a mail carrier. The income drop was and is huge for me. I have paid cash for 90% of my tools, but some i have had to charge. I really only need one more tool which is a Thickness planer. I’m holding out for a sale on the Rigid Planer which has all the features I want. Enough about me. I have watched your shop grow from the first video to this video and it has come out beautifully and a model for others to follow, especially your Miter station. Anyone with that amount of space could easily make it with your plans,or just watching the build video’s. You have utilized every inch of that garage perfectly, and I love the idea of having a rolling storage rack for sheet goods that can be moved to you truck to unload and move back into place. You have come along way in a years time. Maybe I should start making bigger item and sell them out front on my lawn, instead of on Etsy. Best of luck always Jay. PS.- I’m wearing your shirt that say’s” Nothing works unless you do”. It’s my motto now.~Dolly

Looking for a great gift for a friend or family member or maybe a Christmas gift? Recommended woodwork projects include a turned wood box with a lid or how to make a jewlery box. New to woodworking? Great! Check out these simple beginner’s woodworking projects. No matter the DIY woodworking project you can find your next gift idea in the wood craft videos listed below.

Just wanted to show gratitude for the inspiration and knowledge you’ve given. As a former science teacher AND compositor/animator, I can really get down with your attention to detail, clear views/instructions, editing skills and work ethic. I’ve been watching your vids here and there since the sawhorses, of which I have my 2 sets. Since then I’ve been taking your lead and built the conduit rack, multi-function TS hold-down jig and a few more. I appreciate being able to mold them into a workable set up for my 12×20 shop. It’s great to see your success and I wish you the best. You’re doing good things, man, so keep it up.


The lower, far left cabinet houses my planer on bottom. Every drawer slide in this miter saw station is a 24” full extension slide except these. To give just a little bit more room when removing the planer for use I opted for 26” full extension slides here. The planer is a DW735 DeWalt planer. When it was in it’s previous setup I gave more info and thoughts on it which can be found here.
Here’s a traditional Swedish farm accessory for gunk-laden soles. The dimensions are not critical, but be sure the edges of the slats are fairly sharp?they’re what makes the boot scraper work. Cut slats to length, then cut triangular openings on the side of a pair of 2x2s. A radial arm saw works well for this, but a table saw or band saw will also make the cut. Trim the 2x2s to length, predrill, and use galvanized screws to attach the slats from underneath. If you prefer a boot cleaner that has brushes, check out this clever project.
A bottle carrier is a bucket like carrier used to carry beer bottles and so. Yes, the same one you must have used to carry your six-pack. Drinker or not, a bottle carrier is a useful item for everyone. It can be used to carry around or store small items around a household. And it is also very easy to build one. I have several of these lying around my house. Also known as wooden beer totes, this is one wood item you will absolutely love to make. It is also super easy to build.
I built my first platform bed by following the steps mentioned in the tutorial and the end result was everything I expected. It was as beautiful as comfortable and strong. It only cost me around $60 to build this one from the scratch. And if I can build it, anyone can. What you need is a little bit of woodworking experience and a lot of confidence. Collect the items as suggested in the video and start working now.
Here’s a traditional Swedish farm accessory for gunk-laden soles. The dimensions are not critical, but be sure the edges of the slats are fairly sharp?they’re what makes the boot scraper work. Cut slats to length, then cut triangular openings on the side of a pair of 2x2s. A radial arm saw works well for this, but a table saw or band saw will also make the cut. Trim the 2x2s to length, predrill, and use galvanized screws to attach the slats from underneath. If you prefer a boot cleaner that has brushes, check out this clever project.

Another awesome thing about this coffee table is that it is also has a storage unit. So you can store drinks, and other stuff in the half barrel of your table and then close or open it whenever you need. Pete has also constructed a video for this tutorial for which you can find the link below. It illustrates the same process in a video guide that shows you the exact process to be followed while building this whiskey barrel coffee table.
Cut off a 21-in.-long board for the shelves, rip it in the middle to make two shelves, and cut 45-degree bevels on the two long front edges with a router or table saw. Bevel the ends of the other board, cut dadoes, which are grooves cut into the wood with a router or a table saw with a dado blade, cross- wise (cut a dado on scrap and test-fit the shelves first!) and cut it into four narrower boards, two at 1-3/8 in. wide and two at 4 in.
MATERIAL CONNECTION DISCLOSURE: You should assume that this website has an affiliate relationship and/or another material connection to the persons or businesses mentioned in or linked to from this page and may receive commissions from purchases you make on subsequent web sites. You should not rely solely on information contained in this email to evaluate the product or service being endorsed. Always exercise due diligence before purchasing any product or service. This website contains advertisements.

The bandsaw has a 6-3/8” resaw capacity. I find this to be enough for my needs but after recently acquiring some larger chunks of a bradford pear tree that came down in a storm I realized it would be nice to have greater resaw capacity just for getting larger chunks into usable sizes. I don’t think that has justified an upgrade to a larger bandsaw or a riser block kit for me though.
To the left of the cabinet hangs my table saw infeed support arms, my table saw spline jig, multifunction hold down jig, and a dry erase board I made several years ago for my wife. We never put it to use in the house so I put it in my shop. Below that is a rolling mechanics tool box. I store all of my wrenches, sockets, and tools of that nature in it.
Manufacturers that produce woodworking tools and materials have got into the content creation game, too, and some will share woodworking plans online. Minwax and Ryobi, for example, provides their plans free of charge, and Rockler offers their woodworking plans for a fee. Seek them out along with the other blogs and you’ll have a handy list of resources you can turn to for any project.
×