Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.
We cut the supports 16 in. long, but you can place the second shelf at whatever height you like. Screw the end supports to the walls at each end. Use drywall anchors if you can’t hit a stud. Then mark the position of the middle supports onto the top and bottom shelves with a square and drill 5/32-in. clearance holes through the shelves. Drive 1-5/8-in. screws through the shelf into the supports. You can apply this same concept to garage storage. See how to build double-decker garage storage shelves here.
Tucked in the lower left corner of the miter saw station is my DeVilbiss 5hp 20 gallon air compressor. It’s an oil free compressor so it’s loud and obnoxious when running. I don’t use it enough to justify the trouble of making a sound deadening enclosure or putting it outside so for the mean time I’m quite happy with keeping it in here and out of the way. The white hose in the picture is an extra hose that I rarely use. I have the compressor hooked up to a retractable hose reel located just above my dust collector.
Another awesome thing about this coffee table is that it is also has a storage unit. So you can store drinks, and other stuff in the half barrel of your table and then close or open it whenever you need. Pete has also constructed a video for this tutorial for which you can find the link below. It illustrates the same process in a video guide that shows you the exact process to be followed while building this whiskey barrel coffee table.
Cut off a 21-in.-long board for the shelves, rip it in the middle to make two shelves, and cut 45-degree bevels on the two long front edges with a router or table saw. Bevel the ends of the other board, cut dadoes, which are grooves cut into the wood with a router or a table saw with a dado blade, cross- wise (cut a dado on scrap and test-fit the shelves first!) and cut it into four narrower boards, two at 1-3/8 in. wide and two at 4 in.
To the left of the cabinet hangs my table saw infeed support arms, my table saw spline jig, multifunction hold down jig, and a dry erase board I made several years ago for my wife. We never put it to use in the house so I put it in my shop. Below that is a rolling mechanics tool box. I store all of my wrenches, sockets, and tools of that nature in it.
Yes, another website with a simple design. However, they are high in content and offer great woodworking plans for a whole range of interesting and easy to do projects. iBuiltIt.ca has been around for a while, and is a well-respected online real-estate, mostly because of their quality plans. Their plans are ideal for both beginners and experts alike.

And while it would be ideal to limit our workshop to work­shop stuff only, we often find things like gardening tools and general household stuff encroaching on our shop space. If it can’t be helped, it’s best to dedicate a corner for non-shop stuff and limit it to that area. In my shop, I have an area cor­doned off with a salvaged bi-fold door which quarantines the garden tools.


Directly behind my table saw is my 4′ x 8′ modified Paulk workbench that I consider my assembly table as well as an outfeed table. Here’s a shot of the back side of it. I currently have a bunch of 2×10 material on it for an upcoming project and really didn’t want to unload it just for the picture. You can see completed pictures of the project with all of my modifications and changes here.
Get perfectly, consistently spaced and centered shelf-pin holes! Economical and practical, this jig can be used on assembled or unassembled cabinetry. Re-designed handle includes two storage compartments for self-centering bits! Ideal for adding shelves to new or existing cabinets. Drills holes either 1-7/16" or 2-1/2" from edge. Insert shelf pin in top or bottom position to extend jig for continuous drilling. Shelving Jigs measure 20" long Additional Self-Centering Bits available. 
Get perfectly, consistently spaced and centered shelf-pin holes! Economical and practical, this jig can be used on assembled or unassembled cabinetry. Re-designed handle includes two storage compartments for self-centering bits! Ideal for adding shelves to new or existing cabinets. Drills holes either 1-7/16" or 2-1/2" from edge. Insert shelf pin in top or bottom position to extend jig for continuous drilling. Shelving Jigs measure 20" long Additional Self-Centering Bits available. 
As with many of you out there I always enjoy checking out a shop tour. I hope you were able to take away at least something from this shop tour. If you would like to see some reader shop tours that have already been featured on this website you can do so here. If you would like your shop to be featured on this website feel free to drop me a line using my contact form. Thanks for stopping by folks and have a great day!
So that takes care of the center of my shop. I’ll work my way around the perimeter starting at the right wall and moving left. The first item is my rolling plywood cart. I built this a few weeks ago to replace my unsuccessful stationary plywood rack. It’s an 8′ plywood cart that stores full sheets of plywood on one side and off-cuts on the other side. Because it’s on casters I can easily push it outside next to my truck to load it up and also push the entire cart behind the table saw to reduce the distance I need to carry full sheets to be cut down. It’s the design in issue 205 of Wood Magazine.
A small oak table is a very useful wooden item for every household. You can yourself make a nice, strong and beautiful oak table suitable for any purpose. See the image below. As you can see, it is a small, yet good enough table to be used as a coffee table, lamp stand, breakfast table, etc. You can also find many other design variants on the internet. Choose the one you want for yourself and start making it now.
Although refrigerators long ago rendered them obsolete, antique oak ice boxes remain popular with collectors, even though they’re expensive and hard to find. This do-it-yourself version is neither: it’s both inexpensive and easy to build. An authentic reproduction of an original, the project is especially popular when used as a bar, but it has many

Relax and enjoy your outdoor space with this smart patio combo consisting of a sofa and chair. You can adjust the size completely to make it fit perfectly onto your patio or deck, and both the sofa and chair have arms that double as trays for al fresco dining. And you can make your own cushions to fit, or use shop-bought ones and add your own ties, if necessary.

Lumber and supplies are moved in and out of the shop through the front overhead door. To the left of the door are the lumber and plywood storage racks. Across from the lumber rack and to the right of the overhead door is the radial arm saw, miter saw and mortise utilizing a single fence system for all operations. Below and above these are cabinets and storage for misc. power hand tools. Next to the radial arm saw and in the corner is the floor drill press with accessory storage next to it for all drilling operations.  Across from the radial arm saw is a separate workstation set up with a small portable table saw and router set-up with storage underneath for routers, bits and accessories.


Do you want to use an oil stain, a gel stain, a water-based stain or a lacquer stain? What about color? Our ebook tells you what you really need to know about the chemistry behind each wood stain, and what to expect when you brush, wipe or spray it on. It’s a lot simpler than you think! This is the comprehensive guide to all the varieties of stain you will find at the store and how to use them.
×