You can transfer a graphic on any wood piece of your choice, including a frame, top of a table, etc. The surface should be clean and big enough for the graphic paper. I am also sharing a video tutorial here that explains in detail the process of transferring any graphic to a wooden surface using a freezer paper. Just gather the items you need and follow this video to carve your favorite designs on your favorite wood items.
Moving left is my vertical tool area. Most noticeably are the Detroit sports flags on the wall. I grew up just west of Detroit in Livonia Michigan until I was about 14 or 15 when I moved to Mississippi. I absolutely love where I live in Mississippi but you can’t take the sports fan out of a kid. Growing up watching the horrible 1990’s Lions teams really makes me appreciate the current roster.
The next vertical tool is my 13” benchtop drill press. It’s a cheap Harbor Freight model that isn’t perfect but isn’t a bad buy either. It has several flaws that I would consider “areas for improvement” and not problems. I would purchase this again if I had to do it over. I have a larger drill pres table with integrated storage drawers for it but find it to be a little too big for where I currently have the drill press in the shop.
Hey, I want to build all of these (and I did read to the end), but my list of projects is so long that any one of these will have to wait ’til next year (and i don’t mean January). thanks for all these ideas. there is one more i read about in the Handy Family Man. It is an adaptation to your shop vac that puts the hose at your project so it sucks up the dust as it is produced. Wonderful, right? Maybe next year!
To the left of the cart on the wall is my universal clamp rack and finishing supply rack. They are both mounted to the wall with a french cleat. The clamp rack is a universal design I recently made to hold every one of my clamps without having to make specific profile holders for each style clamp. Having them all in one location is very convenient. My finishing supply rack was made in my previous shop and has served me well. I’ve currently outgrown it slightly but I really like the efficiency of storage for finishing supplies. It has a few short shelves for quart size cans and a few shelves for standard spray size cans. I might make a larger version of this in the future.
Spanning 14-1/2′ of the back wall is my miter saw station. Completing this has resulted in a huge increase in storage space, organization, and convenience when using the miter saw. It features 20 drawers and a pull out tray for storing my planer out of the way. Eight upper storage bins are for commonly used items such as my cordless tools as well as other items that don’t need to be stored away from dust. There is integrated dust collection for the miter saw and a stop block to the left of the saw with roughly 106” of capacity.
The shelf in the first picture is made of red oak plywood. You can choose the wood type, color and design as you like for your project. In case if you need more help understanding this project, you can refer the source link below. It discusses various items used, steps and tips and personal experience of the author who personally built a Zigzag shelf.
Cut off a 21-in.-long board for the shelves, rip it in the middle to make two shelves, and cut 45-degree bevels on the two long front edges with a router or table saw. Bevel the ends of the other board, cut dadoes, which are grooves cut into the wood with a router or a table saw with a dado blade, cross- wise (cut a dado on scrap and test-fit the shelves first!) and cut it into four narrower boards, two at 1-3/8 in. wide and two at 4 in.
Start with ¾" plywood that is twice as wide as the depth of the cabinet and as long as one side and top/bottom. I crosscut the top and bottom off of one end and set it aside. Then, using a ½" dado stack in my table saw, I cut a series of ¼" deep dadoes across the sides. Make the spacing between them uniform so that the drawers are interchangeable. Finally, rip the sides and top/bottom in half to separate them and assemble the cabinet however you please. If you want to hang it on a wall, attach a French cleat to the back at the top and a batten of equal thickness at the bottom.
Learning from the ideas of other woodworkers, while avoiding their mistakes is an excellent way to design and set-up your own shop layout. Setting up a woodworking shop as a hobby place, or for a some one more serious, who even may venture off into some sort of woodworking business; is not as easy as it might sound. Knowing the correct steps to follow will save you time and money, but it will also save you a lot of stress down the road.
The cost of being disorganized is time. It takes me ten times as long to work on a project when I am scouring the room looking for a drill bit, the right screws, or trying to remember where I last used one of my 10 tape measures. Workshop organization is an ongoing project. As you acquire more tools, you have to rearrange your shop to work in storage for those new items. So mobile and modular storage, wherever possible will save you time down the road. Here are some amazing Workshop Organization Ideas that I hope will inspire you!
It might not be the easiest project in this list, but if you already have some experience with wood cutting and joinery, it won’t be any hassle at all. Thanks to the extremely detailed instructions it shouldn’t really be a problem even if you’re not very familiar with woodworking. This could actually be a great project for refining your woodworking skills as a beginner!