Below the top structure I mounted a long power outlet bar to have a convenient power location for whatever corded tool I am using at the table. Below that is the lower shelf which I built specifically to house my X-Carve CNC machine. This machine has 1000mm rails so making a dedicated cart for it would take up quite a bit of valuable floor space. The idea behind storing it on this shelf was so that I could easily slide it off and place it on the top work surface to use it. However, I haven’t actually removed it from it’s current location yet. I can use it where it is with no problems.
Lumber and supplies are moved in and out of the shop through the front overhead door. To the left of the door are the lumber and plywood storage racks. Across from the lumber rack and to the right of the overhead door is the radial arm saw, miter saw and mortise utilizing a single fence system for all operations. Below and above these are cabinets and storage for misc. power hand tools. Next to the radial arm saw and in the corner is the floor drill press with accessory storage next to it for all drilling operations.  Across from the radial arm saw is a separate workstation set up with a small portable table saw and router set-up with storage underneath for routers, bits and accessories.
Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
Another awesome thing about this coffee table is that it is also has a storage unit. So you can store drinks, and other stuff in the half barrel of your table and then close or open it whenever you need. Pete has also constructed a video for this tutorial for which you can find the link below. It illustrates the same process in a video guide that shows you the exact process to be followed while building this whiskey barrel coffee table.
There’s nine more drawers that I didn’t take interior pictures of because it’s just generic stuff. But I will go through the contents for you. Top to bottom in the left column is a drawer for manuals, a drawer for every letter that I have received from all of you out there, and a drawer for my electrical tools and supplies. Top to bottom in the center column is a drawer for miscellaneous hand tools that are more general household and carpentry related such as pry bars, putty knives, and drywall tools, a drawer for hammers, mallets and squares, and a drawer for all of my hand held cutting tools like handsaws, knives, and chisels. Top to bottom in the third column is a drawer for all types of brushes, a drawer for all of my sanding tools and supplies, and a drawer for all of my router bits and attachments.
Their free woodworking plans are well-illustrated, easy to follow and best of all – free. You can’t beat that! Their plans are directly available on their website for easy viewing and printing. You do not have to download any PDF files. It is an easy point and click, with several dozens of in-depth plans available for free, all for your viewing pleasure.
If you bought this superb polished table in a store, it would cost you a fortune, but our detailed instructions will help you make one for less than $100. And it looks like highly polished stone, but no-one would know it’s actually made from concrete with a wooden base. Also, you can embellish the top with leaf prints, like the table shown here, or personalize it with glass or mosaic tiles or imprints of seashells.
The drawers are very simple to make. First, cut the drawer bottoms from ½" plywood. Make them about 1/16" narrower than the distance between the dadoes and full length. Cut strips of solid wood or plywood equal to the inside depth of the drawers you want and cross-cut them to length. I assem­ble the drawers with glue and nails. Note that to store a 5" tall object, you don’t need a 5"-deep drawer – you just need 5" of headroom.
In my machine shop, I store my thickness planer under the infeed table of my jointer. The feed direction of the planer is one direction and the jointer the other. This works especially well because I can joint all my boards and stack them on a cart or sawhorses; then, without reorienting them, I can feed them through the planer (after I pull it out, of course).
You can also make one for elders and put it in your garden or terrace or anywhere in the house. Elders can use it to relax and kids can use it to play or sleep. Although this is a really beautiful piece of woodwork, it is not that easy to make. Only someone with good woodworking skill can think of making this swing set. Also, I couldn’t find a good tutorial that illustrates the process of building a wooden boat-shaped swing set. Most Probably, I will write one when I build mine.But if you really want this swing set like right now, I would suggest you hire a good woodworker, who can build something similar. Or just search the internet and maybe you get lucky enough to find a tutorial for this. Good luck either way.
My second shop (2012) is where I started this whole YouTube and website venture. I was maintenance at an apartment complex which allowed me the opportunity to clean out a junk apartment that was previously used for storage and use it as a shop. At that time the only woodworking tool I had was a Kobalt 10” sliding miter saw from my previous shop. I used it to build my wife’s grandmother a 2×4 sitting bench and the positive feedback from friends and family fueled the fire to get back into woodworking. I took an initial $200 investment from my household income to batch out a bunch of them to sell. That investment and a lot of sweat was the beginning of a snowball that has become my shop.
Looking for a great gift for a friend or family member or maybe a Christmas gift? Recommended woodwork projects include a turned wood box with a lid or how to make a jewlery box. New to woodworking? Great! Check out these simple beginner’s woodworking projects. No matter the DIY woodworking project you can find your next gift idea in the wood craft videos listed below.
Yes, another website with a simple design. However, they are high in content and offer great woodworking plans for a whole range of interesting and easy to do projects. iBuiltIt.ca has been around for a while, and is a well-respected online real-estate, mostly because of their quality plans. Their plans are ideal for both beginners and experts alike.
Manufacturers that produce woodworking tools and materials have got into the content creation game, too, and some will share woodworking plans online. Minwax and Ryobi, for example, provides their plans free of charge, and Rockler offers their woodworking plans for a fee. Seek them out along with the other blogs and you’ll have a handy list of resources you can turn to for any project.
×