Each issue of Wood News , our online woodworking magazine, features a different home workshop, and we've compiled 10 of these features here. Browsing them is a great way to find new ideas on how to set up your own shop, or if you just want to see innovative ways other woodworkers have approached the various shop setup issues we all face. From space considerations and smart storage ideas to the various tool combinations and approaches to woodworking, you'll find something here that's really interesting. Click each image to take a look!
My shop is about 425 square feet, roughly the size of a two-car garage. However, there is a wall running down the middle with a sliding glass door at one end that reduces the openness. It also increases my wall space. Plus, I have all my machinery on one side of the wall, so all the dust and noise stays out of the bench room. In this article, I want to share with you some of the things that make my shop such a nice place to practice my craft and give you ideas of how to make the most of the space you have.
Below is a list of my top 12 DIY woodworking websites. This list is in no particular order and is by no means meant to be a comprehensive list. There is so much free and paid information available for DIY woodworkers at all skilled levels on the web, it would be impossible to list them all. As always, please support these sites by visiting them, leaving a comment, buying a plan, following them on social media, etc. Please let me know your favorite woodworking websites that I left of the list, enjoy!
The lower, far left cabinet houses my planer on bottom. Every drawer slide in this miter saw station is a 24” full extension slide except these. To give just a little bit more room when removing the planer for use I opted for 26” full extension slides here. The planer is a DW735 DeWalt planer. When it was in it’s previous setup I gave more info and thoughts on it which can be found here.
It’s been a solid year since moving into this house and starting my shop. Nearly everything in my shop is on casters for mobility. In my opinion the most important tool in any woodshop is the table saw so lets start there. My table saw is a SawStop PCS with 52” rip capacity. The attention to detail on this machine is phenomenal. I have the industrial mobile base for it which makes the single heaviest item in my shop one of the easiest to move. The base lifts the entire saw, including the extension wing, several inches with ease. It is actually in the up position in the following image. I also spray painted the location of the extension wing supports on the ground so I can easily locate a familiar position when setting up the saw. Because moving it around the shop on the mobile base is effortless I find myself moving it out of the way frequently when I know I’m not going to be using it for a while. I also keep a couple trash cans near the table saw.
To corral shelf-dwelling books or DVDs that like to wander, cut 3/4-in.-thick hardwood pieces into 6-in. x 6-in. squares. Use a band saw or jigsaw to cut a slot along one edge (with the grain) that’s a smidgen wider than the shelf thickness. Stop the notch 3/4 in. from the other edge. Finish the bookend and slide it on the shelf. Want to build the shelves, too? We’ve got complete plans for great-looking shelves here.
A woodworker's Workbench is a special type of bench designed to hold your work when you are working on a wood project. The main purpose of this table is to keep the woodwork steady and to prevent it from moving. Follow the tutorial below to build yourself a nice workbench suitable for your specific woodworking projects. Make sure to modify the table to fit your specific requirements.
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
To the left of the cart on the wall is my universal clamp rack and finishing supply rack. They are both mounted to the wall with a french cleat. The clamp rack is a universal design I recently made to hold every one of my clamps without having to make specific profile holders for each style clamp. Having them all in one location is very convenient. My finishing supply rack was made in my previous shop and has served me well. I’ve currently outgrown it slightly but I really like the efficiency of storage for finishing supplies. It has a few short shelves for quart size cans and a few shelves for standard spray size cans. I might make a larger version of this in the future.
When I built the cabinet that houses my marking and measuring tools, I wanted to make sure each tool had its own spot and would stay fixed. I cut the drawer bottoms and used contact cement to adhere ¼" cork sheet to one side. Using an X-acto knife, I cut around each tool, then peeled the cork off the plywood with a chisel. I made the handles with hand planes, cut them to length and glued them to the fronts using a rubbed hot hide glue joint.
This is one of those things that you never know you need unless you have one. This amazing wooden sofa sleeve works perfectly on either or both sides of a sofa set. It gives your sofa a nice look. The sleeve can also be modified to include a cup holder, mobile holder, etc. You can easily find this item on any online furniture store, but an even better idea is to build one. This way, you can make a sofa sleeve design that you actually like and make space for cup and other things.
Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience.
My dedicated shop space is about 8′ x 4′, the rest is a one car garage that needs to stay open for my wife’s car. I will sometimes set up some plywood and sawhorses in that space for assembly though. The section that is my dedicated shop has a floor made of 2″x6″ lumber stretched out over joists on top of dirt. It is an old floor filled with knot holes, cracked or broken boards (with temporary plywood screwed over them) and just generally uneven. If I cannot build a shed as my new workshop I will be looking at redoing the floor in my current space. Not sure how I would go about it though.