Plywood and long stock can also be a challenge to store in a shop. When I had an 8' bank of cabinets in my shop, I used to slide my sheet goods in behind it. Now that they are gone, I just stand them up against the wall and use a wedge system to keep them neat and upright. Long, narrow material goes on my lumber rack beside my table saw. I also store dry lumber standing on end in one corner of my bench room.
The procedure is very easy to understand and follow for anyone with a little woodworking knowledge. Make sure to collect all the items you need before you start with the project. You may even ask Tracy your queries directly in the comment section of the tutorial post. Or you can ask them here. Either way, I hope that you manage to build this one nicely.
And this is the front side which is where I primarily stand when using the table. The top surface has 3/4” holes on 4” centers to allow clamping material pretty much anywhere on the table. It also features a hollow torsion box design for added stiffness to the top surface and empty space just below the work surface to place hand tools out of the way when working on something.
The space behind a door is a storage spot that’s often overlooked. Build a set of shallow shelves and mount it to the wall behind your laundry room door. The materials are inexpensive. Measure the distance between the door hinge and the wall and subtract an inch. This is the maximum depth of the shelves. We used 1x4s for the sides, top and shelves. Screw the sides to the top. Then screw three 1×2 hanging strips to the sides: one top and bottom and one centered. Nail metal shelf standards to the sides. Complete the shelves by nailing a 1×2 trim piece to the sides and top. The 1×2 dresses up the shelf unit and keeps the shelves from falling off the shelf clips.
French cleats are a simple way to hang things on walls while allowing easy repositioning. One bevelled cleat is fastened to the wall and the other is fastened to whatever you want to hang. One catches the other and gravity does the rest. French cleats are commonly cut at 45 degrees but I prefer to cut mine at around 30 degrees. This makes them easier to lift off the wall (especially way up high) without sacrificing security.
The lower, far left cabinet houses my planer on bottom. Every drawer slide in this miter saw station is a 24” full extension slide except these. To give just a little bit more room when removing the planer for use I opted for 26” full extension slides here. The planer is a DW735 DeWalt planer. When it was in it’s previous setup I gave more info and thoughts on it which can be found here.
To the left of the cabinet hangs my table saw infeed support arms, my table saw spline jig, multifunction hold down jig, and a dry erase board I made several years ago for my wife. We never put it to use in the house so I put it in my shop. Below that is a rolling mechanics tool box. I store all of my wrenches, sockets, and tools of that nature in it.
MATERIAL CONNECTION DISCLOSURE: You should assume that this website has an affiliate relationship and/or another material connection to the persons or businesses mentioned in or linked to from this page and may receive commissions from purchases you make on subsequent web sites. You should not rely solely on information contained in this email to evaluate the product or service being endorsed. Always exercise due diligence before purchasing any product or service. This website contains advertisements.
By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.
Lumber and supplies are moved in and out of the shop through the front overhead door. To the left of the door are the lumber and plywood storage racks. Across from the lumber rack and to the right of the overhead door is the radial arm saw, miter saw and mortise utilizing a single fence system for all operations. Below and above these are cabinets and storage for misc. power hand tools. Next to the radial arm saw and in the corner is the floor drill press with accessory storage next to it for all drilling operations. Across from the radial arm saw is a separate workstation set up with a small portable table saw and router set-up with storage underneath for routers, bits and accessories.
Google is probably the first place where most people would start searching for woodworking plans, but often the top results can be a mix of articles and how-to pieces that just aren’t detailed enough. Sometimes they’ll link to the plans (like we try to here at Lifehacker), but other times, they’re just showing off a cool project. There are better, more precise ways of finding what you’re looking for.