Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!
My shop is about 425 square feet, roughly the size of a two-car garage. However, there is a wall running down the middle with a sliding glass door at one end that reduces the openness. It also increases my wall space. Plus, I have all my machinery on one side of the wall, so all the dust and noise stays out of the bench room. In this article, I want to share with you some of the things that make my shop such a nice place to practice my craft and give you ideas of how to make the most of the space you have.
Tucked in the lower left corner of the miter saw station is my DeVilbiss 5hp 20 gallon air compressor. It’s an oil free compressor so it’s loud and obnoxious when running. I don’t use it enough to justify the trouble of making a sound deadening enclosure or putting it outside so for the mean time I’m quite happy with keeping it in here and out of the way. The white hose in the picture is an extra hose that I rarely use. I have the compressor hooked up to a retractable hose reel located just above my dust collector.
Likewise, I keep all the tools nearby that are required to make adjustments to my machinery. In the center of my machine shop, I keep metric and imperial wrenches and hex keys, a machinist’s square, a stepped height gauge and a multi-bit screwdriver. I try to store machine-specific accessories such as blades and wrenches within a step of the machine. My table-saw blades are stored on the wall to the left of my table-saw, but I prefer how editor Rob Brown stores his blades.

Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.

Although refrigerators long ago rendered them obsolete, antique oak ice boxes remain popular with collectors, even though they’re expensive and hard to find. This do-it-yourself version is neither: it’s both inexpensive and easy to build. An authentic reproduction of an original, the project is especially popular when used as a bar, but it has many
Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!
Spanning 14-1/2′ of the back wall is my miter saw station. Completing this has resulted in a huge increase in storage space, organization, and convenience when using the miter saw. It features 20 drawers and a pull out tray for storing my planer out of the way. Eight upper storage bins are for commonly used items such as my cordless tools as well as other items that don’t need to be stored away from dust. There is integrated dust collection for the miter saw and a stop block to the left of the saw with roughly 106” of capacity.

Each issue of Wood News , our online woodworking magazine, features a different home workshop, and we've compiled 10 of these features here. Browsing them is a great way to find new ideas on how to set up your own shop, or if you just want to see innovative ways other woodworkers have approached the various shop setup issues we all face. From space considerations and smart storage ideas to the various tool combinations and approaches to woodworking, you'll find something here that's really interesting. Click each image to take a look!


Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
My second shop (2012) is where I started this whole YouTube and website venture. I was maintenance at an apartment complex which allowed me the opportunity to clean out a junk apartment that was previously used for storage and use it as a shop. At that time the only woodworking tool I had was a Kobalt 10” sliding miter saw from my previous shop. I used it to build my wife’s grandmother a 2×4 sitting bench and the positive feedback from friends and family fueled the fire to get back into woodworking. I took an initial $200 investment from my household income to batch out a bunch of them to sell. That investment and a lot of sweat was the beginning of a snowball that has become my shop.
And while it would be ideal to limit our workshop to work­shop stuff only, we often find things like gardening tools and general household stuff encroaching on our shop space. If it can’t be helped, it’s best to dedicate a corner for non-shop stuff and limit it to that area. In my shop, I have an area cor­doned off with a salvaged bi-fold door which quarantines the garden tools.
For your kitchen, it can work as a knife rack. It gives you easy access to all essential tools while saving space. In addition, it adds a nice visual appeal to your kitchen wall. You can customize your wall rack with different materials, designs and styles. I am here sharing the source link to the step by step tutorial about how to make a rustic wall knife rack.
Some tools required for this project are hole saw, drilling machine, pencil, tape measure, clamps, etc. This tutorial explains every step properly with images so that anyone can make a wooden sofa sleeve easily. Those, who prefer a video tutorial, can visit the below link to a YouTube video that illustrates the process of building a DIY Sofa Sleeve Cupholder.
Tucked in the lower left corner of the miter saw station is my DeVilbiss 5hp 20 gallon air compressor. It’s an oil free compressor so it’s loud and obnoxious when running. I don’t use it enough to justify the trouble of making a sound deadening enclosure or putting it outside so for the mean time I’m quite happy with keeping it in here and out of the way. The white hose in the picture is an extra hose that I rarely use. I have the compressor hooked up to a retractable hose reel located just above my dust collector.
A lot of woodworkers share their projects through their own blogs or YouTube channels. In fact, we’ve shared many of them here before, including, Woodworking for Mere Mortals, The Wood Whisperer, Matthias Wandel, April Wilkerson, Sawdust Girl, House of Wood, FixThisBuildThat, Pneumatic Addict, Build-Basic, Rogue Engineer, Her Tool Belt, and Ana White. The best YouTube woodworkers create great videos, but also provide a complete blog post with a cut list, tools, materials, and instructions. Find your favorites and save them for when you’re doing your searches.
×