Who doesn’t want to have one awesome and handy wooden desk organizer that not only looks beautiful but can store all your mini office desk items properly? See the picture below. I am sure you will love this one. I have already built one myself as I just could not resist having one at my office. This thing easily stores all my office desk essentials, including pen, pencils, marker, small notebooks, etc. in the most organized way. You can see it yourself.
My shop is about 425 square feet, roughly the size of a two-car garage. However, there is a wall running down the middle with a sliding glass door at one end that reduces the openness. It also increases my wall space. Plus, I have all my machinery on one side of the wall, so all the dust and noise stays out of the bench room. In this article, I want to share with you some of the things that make my shop such a nice place to practice my craft and give you ideas of how to make the most of the space you have.
about me back-office functions best tools business acounting business of woodworking business spreadsheet butcher block cutting board cutting board construction cutting board feet cutting board handles diy DIY project Do It Yourself end grain end grain cutting board constuction end grain flattening free woodworking plans getting started growing instagram hand tools how to make a cutting board how to start woodworking instagram Instagram for woodworkers Magnetic Knife Rack maker maker accounting maker business making a cutting board power tools router jig rubber cutting board feet social media tax accounting tools turning a hobby into a business vintage tools which tools should i get wood cutting board feet woodworker woodworking woodworking accounting woodworking business woodworking tools
This is probably one the easiest woodworking projects you will find here. Although easy, a doormat is an equally important and useful item for households. As you can see in the image below, you will only need some 2X2 wooden boards and rope to build a simple doormat. This doormat is mostly useful for outdoor and porch. It will easily remove all the mud from your shoes with just one wipe. It is also very easy to clean and looks fabulous even if it is dirty.
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
Drawers are really useful in a wood shop – you can’t have enough. They keep out the dust and with dividers or compart­ments they can help organize as well. A drawer that is too deep ends up getting filled with anything that fits and becomes a junk drawer, so multiple shallow drawers are better than one deep drawer. However, drawer slides can be expensive so I make my own drawers with built-in drawer slides. In addition to saving costs, if I make multiple cabinets the same width, I can move drawers from one cabinet to another quickly and easily.
Drill four 5/8-in.-dia. 1/2-in.-deep holes on the large disc?inside the traced circle?then use 5/8-in. dowel centers to transfer the hole locations to the underside of the small disc. Drill four 1/2-in.-deep holes on the underside of the small disc and a 1/2-in.-deep hole in the center of the top for the dowel handle. Glue in the dowels to join the discs, and glue in the handle. We drilled a wood ball for a handle knob, but a screw-on ceramic knob also provides a comfortable, attractive grip.
Cut off a 21-in.-long board for the shelves, rip it in the middle to make two shelves, and cut 45-degree bevels on the two long front edges with a router or table saw. Bevel the ends of the other board, cut dadoes, which are grooves cut into the wood with a router or a table saw with a dado blade, cross- wise (cut a dado on scrap and test-fit the shelves first!) and cut it into four narrower boards, two at 1-3/8 in. wide and two at 4 in.
My first woodworking “shop” was in the living room and kitchen of a run-down house trailer (2008-ish). Nothing pretty at all but it was functional. At that time I was living on my own with a job paying just over minimum wage. The engine in my truck blew a head gasket and the only option for me to rebuild the engine without going into debt was to sell off my woodshop. I sold everything but my miter saw. It was a hard lesson learned on being prepared with an emergency fund and I’ll never put myself in that kind of situation again.
This is not a guide to shop layout. That may, in fact come later, depending on how much time I devote to this web site. These are important issues that you must consider as you design your shop. My shop is in my garage. Even as we were picking out house designs I knew it would be in my garage. That means that there isn’t a time since we decided to build that I haven’t been considering these issues, and planning and changing plans. That is the nature of it. I knew what I would settle for as a minimum, and made sure it was expendable enough to ensure I could change my mind if I needed or wanted.

This rack can be built from old unused wood pallets you can find around the house. So it is also a great way to recycle those old pallets. You can also find a step by step tutorial at instructables.com for which I have included the source link below. This tutorial helps you to make a wood wine rack from the scratch. So what are waiting for? Just grab the items you need and start building a cool wooden rack for those nice wine bottles of yours.

Drawers are really useful in a wood shop – you can’t have enough. They keep out the dust and with dividers or compart­ments they can help organize as well. A drawer that is too deep ends up getting filled with anything that fits and becomes a junk drawer, so multiple shallow drawers are better than one deep drawer. However, drawer slides can be expensive so I make my own drawers with built-in drawer slides. In addition to saving costs, if I make multiple cabinets the same width, I can move drawers from one cabinet to another quickly and easily.
To the left of the cart on the wall is my universal clamp rack and finishing supply rack. They are both mounted to the wall with a french cleat. The clamp rack is a universal design I recently made to hold every one of my clamps without having to make specific profile holders for each style clamp. Having them all in one location is very convenient. My finishing supply rack was made in my previous shop and has served me well. I’ve currently outgrown it slightly but I really like the efficiency of storage for finishing supplies. It has a few short shelves for quart size cans and a few shelves for standard spray size cans. I might make a larger version of this in the future.
The beauty of this project lies in the simplicity. All you need are 3 pieces of wood of your choice (though we must admit natural hardwoods will look incredible), sanding block, clamps, wood glue and finishing product. The hardest step of the whole tutorial is measuring – as always, measure 9 times, cut once! You wouldn’t want to finish your project and then realize it doesn’t have enough space to fit your DVD player, would you?
×