The cost of being disorganized is time. It takes me ten times as long to work on a project when I am scouring the room looking for a drill bit, the right screws, or trying to remember where I last used one of my 10 tape measures. Workshop organization is an ongoing project. As you acquire more tools, you have to rearrange your shop to work in storage for those new items. So mobile and modular storage, wherever possible will save you time down the road. Here are some amazing Workshop Organization Ideas that I hope will inspire you!
Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!
Wall-mounted or placed on a table or countertop, this handsome display cabinet is the perfect way to share any collection while keeping it clean and protected at the same time. Featuring tempered glass doors and three shelves, the cabinet’s design calls for all straight cuts and straightforward construction techniques (simple cut-outs give the effect of
From the image above it seems that you do not require a big tutorial to help you to build this candle holder. All you need is a wood panel, a hook and some nails/screws and do exactly what you see in the picture. Attach the hook to the wood panel using two screws and then, attach the panel to the wall using more nails or screws. That’s it. I hope this gets the job done.
The lower, far left cabinet houses my planer on bottom. Every drawer slide in this miter saw station is a 24” full extension slide except these. To give just a little bit more room when removing the planer for use I opted for 26” full extension slides here. The planer is a DW735 DeWalt planer. When it was in it’s previous setup I gave more info and thoughts on it which can be found here.
Building a Wooden Office Desk Organizer is an easy task for a professional woodworker, but not so much for normal people like you and me. But that doesn’t mean you cannot do this. Two years ago, I had almost no woodworking experience, but now I make most of my household and office wooden items by myself. This saves me a lot of money. And believe me when I say this; you can also manage to make wonderful wood items with a little practice and some woodworking experience.
Slice, dice and serve in style on this easy, attractive board. We’ll show you a simple way to dry-fit the parts, scribe the arc and then glue the whole thing together. We used a 4-ft. steel ruler to scribe the arcs, but a yardstick or any thin board would also work. Find complete how-to instructions on this woodworking crafts project here. Also, be sure to use water-resistant wood glue and keep your board out of the dishwasher or it might fall apart. And one more thing: Keep the boards as even as possible during glue-up to minimize sanding later. For great tips on gluing wood, check out this collection.
Building a Wooden Office Desk Organizer is an easy task for a professional woodworker, but not so much for normal people like you and me. But that doesn’t mean you cannot do this. Two years ago, I had almost no woodworking experience, but now I make most of my household and office wooden items by myself. This saves me a lot of money. And believe me when I say this; you can also manage to make wonderful wood items with a little practice and some woodworking experience.
Day in and day out we all deal with electricity, but it seems to be some illusive concept that few woodworkers really understand. Electricity drives our tools, and drives our everyday life. Electricity has the versatility to replace many older forms of energy. Without it we would still be using lanterns for light, fires for heat, and oxen for work.
Great Shop… My wife is hinting at my earliest convenience to start my garage project. We’re changing the one car garage into a half his and half hers… I am a handyman, so i don’t just do one thing. So I am many types of tools…the working space will be 10×13 and have a loft. I have had to take my miter saw with me on occasional jobs, but am thinking about a miter saw station. Any suggestions?
Moving left is my vertical tool area. Most noticeably are the Detroit sports flags on the wall. I grew up just west of Detroit in Livonia Michigan until I was about 14 or 15 when I moved to Mississippi. I absolutely love where I live in Mississippi but you can’t take the sports fan out of a kid. Growing up watching the horrible 1990’s Lions teams really makes me appreciate the current roster.
By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking.   These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email orderdesk@canadianwoodworking.com  and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence. 
You can also use Google image search to research a project. Unlike the PDF search, the image search provides a photo of what the project will look like, which is helpful in determining if you want to pursue building it. By doing an image search for how to build a step stool, you will have a ton of options that all lead to woodworking plans of various quality. (The how to part of these is important—otherwise you’ll just get pictures of step stools.)
×