Though our shops never seem to be spacious enough, how you store what’s inside can make the difference between a neat, organized work space and a disaster zone. The first priority is to have a good look at what’s in your shop and decide how often you use it. Things that you never use have no place in a tight shop. Items that you use only rarely or are overstock should be stored on a top shelf or in another room – not on the prime, easy-access shelves. I have laid claim to a few bays of shelving in our storage room. I store all my overstock hardware in full-extension pull-outs so I can find it easily when needed. In the storage room, I also store my benchtop tools that I use less frequently. All are fairly heavy, so I make sure to store them at about waist height to make it easy on my back.
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.

Get perfectly, consistently spaced and centered shelf-pin holes! Economical and practical, this jig can be used on assembled or unassembled cabinetry. Re-designed handle includes two storage compartments for self-centering bits! Ideal for adding shelves to new or existing cabinets. Drills holes either 1-7/16" or 2-1/2" from edge. Insert shelf pin in top or bottom position to extend jig for continuous drilling. Shelving Jigs measure 20" long Additional Self-Centering Bits available. 
Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!
Relax and enjoy your outdoor space with this smart patio combo consisting of a sofa and chair. You can adjust the size completely to make it fit perfectly onto your patio or deck, and both the sofa and chair have arms that double as trays for al fresco dining. And you can make your own cushions to fit, or use shop-bought ones and add your own ties, if necessary.
Copyright 2018 by Cut The Wood. CutTheWood.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Additionally, CutTheWood.com participates in various other affiliate programs, and we sometimes get a commission through purchases made through our links.
Just wanted to show gratitude for the inspiration and knowledge you’ve given. As a former science teacher AND compositor/animator, I can really get down with your attention to detail, clear views/instructions, editing skills and work ethic. I’ve been watching your vids here and there since the sawhorses, of which I have my 2 sets. Since then I’ve been taking your lead and built the conduit rack, multi-function TS hold-down jig and a few more. I appreciate being able to mold them into a workable set up for my 12×20 shop. It’s great to see your success and I wish you the best. You’re doing good things, man, so keep it up.
The tutorial that I am sharing here was written by someone who built this pallet art just to improve the value of a property they wanted to sell fast and they succeed in it. So you can imagine how wonderful this item must look like. I am assuming you do not just want to make this beautiful pallet art so that you can also sell your property easily. Well, whatever your reasons are, this beauty is able to attract anyone who visits your house.
No doubt many of us would love to have a huge, 2000 square foot building devoted to woodcraft, on a wooded acreage somewhere. But there is a reality that goes with a hobby shared by numerous ordinary people: very few really have the means to set up such palatial workshops. We have our lives to lead, and engaging in such a venture is out of the reach for most, myself included. This article is dedicated to workshops for "the rest of us."
Their plans are delivered in a PDF format as part of a vlog series. They have regular episodes in the form of “seasons” and “episodes”. Your head will spin with the sheer number of “episodes” on the website. At the time of writing, it is at season 9, episode 933. A small caveat, though, is that you have to subscribe to their newsletter to download the free plans. No biggie. It’s just something to keep in mind.
This is one of those things that you never know you need unless you have one. This amazing wooden sofa sleeve works perfectly on either or both sides of a sofa set. It gives your sofa a nice look. The sleeve can also be modified to include a cup holder, mobile holder, etc. You can easily find this item on any online furniture store, but an even better idea is to build one. This way, you can make a sofa sleeve design that you actually like and make space for cup and other things.
Lumber and supplies are moved in and out of the shop through the front overhead door. To the left of the door are the lumber and plywood storage racks. Across from the lumber rack and to the right of the overhead door is the radial arm saw, miter saw and mortise utilizing a single fence system for all operations. Below and above these are cabinets and storage for misc. power hand tools. Next to the radial arm saw and in the corner is the floor drill press with accessory storage next to it for all drilling operations.  Across from the radial arm saw is a separate workstation set up with a small portable table saw and router set-up with storage underneath for routers, bits and accessories.
Disclaimer: Although it is my intention to provide accurate plans and clear instructions, not all plans have been tried and tested. Using plans or information found on SawdustGirl.com indicates that you agree with the Terms of Use policy and will accept full responsibility for the process and outcome of any project you attempt. All plans are for private use only. Plans and information published on SawdustGirl.com may not be reproduced, republished or distributed in any manner without written permission from Sandra Powell, Sawdust Girl. Actual projects built using Sawdust Girl plans may be published on your own site without instructions or "tutorial" as long as you provide a link to my original post with full post title or "SawdustGirl.com" as link title.
Slice, dice and serve in style on this easy, attractive board. We’ll show you a simple way to dry-fit the parts, scribe the arc and then glue the whole thing together. We used a 4-ft. steel ruler to scribe the arcs, but a yardstick or any thin board would also work. Find complete how-to instructions on this woodworking crafts project here. Also, be sure to use water-resistant wood glue and keep your board out of the dishwasher or it might fall apart. And one more thing: Keep the boards as even as possible during glue-up to minimize sanding later. For great tips on gluing wood, check out this collection.
Build this handy stool in one hour and park it in your closet. You can also use it as a step to reach the high shelf. All you need is a 4 x 4-ft. sheet of 3/4-in. plywood, wood glue and a handful of 8d finish nails. Cut the plywood pieces according to the illustration. Spread wood glue on the joints, then nail them together with 8d finish nails. First nail through the sides into the back. Then nail through the top into the sides and back. Finally, mark the location of the two shelves and nail through the sides into the shelves. Don’t have floor space to spare? Build these super simple wall-mounted shoe organizers instead!
The cost of being disorganized is time. It takes me ten times as long to work on a project when I am scouring the room looking for a drill bit, the right screws, or trying to remember where I last used one of my 10 tape measures. Workshop organization is an ongoing project. As you acquire more tools, you have to rearrange your shop to work in storage for those new items. So mobile and modular storage, wherever possible will save you time down the road. Here are some amazing Workshop Organization Ideas that I hope will inspire you!
I love a good shop tour, but it’s super motivating to me to hear you say that you built it all in a few years on good old-fashioned hard work. About 8 years ago, I lost an office job and began working with my hands, first doing siding and windows, and now installing home media systems. It has completely changed my work ethic, and my motto now is, “If you ain’t sweating, you ain’t working.”
Tucked in the lower left corner of the miter saw station is my DeVilbiss 5hp 20 gallon air compressor. It’s an oil free compressor so it’s loud and obnoxious when running. I don’t use it enough to justify the trouble of making a sound deadening enclosure or putting it outside so for the mean time I’m quite happy with keeping it in here and out of the way. The white hose in the picture is an extra hose that I rarely use. I have the compressor hooked up to a retractable hose reel located just above my dust collector.
Just wanted to show gratitude for the inspiration and knowledge you’ve given. As a former science teacher AND compositor/animator, I can really get down with your attention to detail, clear views/instructions, editing skills and work ethic. I’ve been watching your vids here and there since the sawhorses, of which I have my 2 sets. Since then I’ve been taking your lead and built the conduit rack, multi-function TS hold-down jig and a few more. I appreciate being able to mold them into a workable set up for my 12×20 shop. It’s great to see your success and I wish you the best. You’re doing good things, man, so keep it up.
The owners, webmasters, administrators, authors and editors, expressly disclaim all and any liability to any person, whether a user of this website or not, in respect of anything and of the consequences of anything done or omitted to be done by any such person in reliance, whether whole or partial, upon the whole or any part of the contents of this website. Please exercise caution when working with any tools or machinery. Follow common safety rules and precautions as outlined in any manuals related to the equipment being used. If advice or other expert assistance is required, the services of a competent professional person should be sought.
Another dead simple website that offers high-quality free woodworking plans for beginners. If you have worked on wood for a long time, the free plans offered on wood gears will be your cup of tea. Their plans are one of the most detailed we have seen yet. The only caveat is, if you want more complex designs, you will have to pay a small fee. But we think it is well worth it!
×