Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
As your interest in woodworking grows, you’ll want to subscribe to a woodworking magazine. This will help feed your new found obsession with articles on tools, techniques, and woodworking plans. As a print magazine subscriber you’ll also gain access to their database of plans on their websites. Popular magazines include, Woodworkers Journal, Fine Woodworking, and Popular Woodworking.
Each issue of Wood News , our online woodworking magazine, features a different home workshop, and we've compiled 10 of these features here. Browsing them is a great way to find new ideas on how to set up your own shop, or if you just want to see innovative ways other woodworkers have approached the various shop setup issues we all face. From space considerations and smart storage ideas to the various tool combinations and approaches to woodworking, you'll find something here that's really interesting. Click each image to take a look!
I recently met a man known among local woodworkers for having a large workshop with a lot of tools. He offered to show me his workshop, and take photographs of it. His workshop covers the entire basement of a large 1800 square foot bungalow. It's difficult to capture this workshop in just a few photos, so I figured I'd include a large number of photos.
One thing I preach is to make use of the area above your head. In my shop, I’ve installed cabinets on the walls that start a few inches over my head and run up to the ceiling. That way they don’t restrict my movements but still provide a lot of extra storage. I’ve also mounted a power bar to the bottom of the cabinets, which makes it really accessible and it can never be blocked. If your cabinets don’t go all the way up to the ceiling, on top is a great place to store long material. For ease of accessibility, smaller items go on the lower shelves while taller items go on the higher shelves.
The table saw is always connected to my dust collector with a couple pieces of 4” flex hose and some 4” sewer and drain PVC pipe and a homemade blast gate. The port on the table saw is at the rear of the cabinet and this particular area of the shop sees the least amount of foot traffic so I have no problem just leaving the ducting on the floor. I also always have a few other cords on the floor here. I see this as the same principle as walking onto a porch. You know the steps are there so you pick up your feet. I know the pipe is there so I pick up my feet. Not a trip hazard in my opinion.
The next vertical tool is my 13” benchtop drill press. It’s a cheap Harbor Freight model that isn’t perfect but isn’t a bad buy either. It has several flaws that I would consider “areas for improvement” and not problems. I would purchase this again if I had to do it over. I have a larger drill pres table with integrated storage drawers for it but find it to be a little too big for where I currently have the drill press in the shop.
This is probably one the easiest woodworking projects you will find here. Although easy, a doormat is an equally important and useful item for households. As you can see in the image below, you will only need some 2X2 wooden boards and rope to build a simple doormat. This doormat is mostly useful for outdoor and porch. It will easily remove all the mud from your shoes with just one wipe. It is also very easy to clean and looks fabulous even if it is dirty.
Lumber and supplies are moved in and out of the shop through the front overhead door. To the left of the door are the lumber and plywood storage racks. Across from the lumber rack and to the right of the overhead door is the radial arm saw, miter saw and mortise utilizing a single fence system for all operations. Below and above these are cabinets and storage for misc. power hand tools. Next to the radial arm saw and in the corner is the floor drill press with accessory storage next to it for all drilling operations. Across from the radial arm saw is a separate workstation set up with a small portable table saw and router set-up with storage underneath for routers, bits and accessories.
Fast forward two and a half years since the start of shop #2. My wife finished college and my online business was at a sustainable point for me to leave my day job which lead us to house shopping. We ended up getting our first house together on July 2nd 2014. The house we found fit literally every one of our criteria including the most important for me which was a two car garage. With an empty garage to start my current shop I gave the walls a fresh coat of white paint and ran new electrical wires for the shop inside a long box along the bottom of the left and rear walls.
I really enjoyed this video. I don’t particularly enjoy watching videos every time someone changes the layout of their shop. But, yours is the exception. I know a lot of your fans have probably been asking for a while for you to do a tour of your shop. Glad you waited till it was all finished to do it. You must’ve shot this video before you got your festool tools.
Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.
Their free woodworking plans are well-illustrated, easy to follow and best of all – free. You can’t beat that! Their plans are directly available on their website for easy viewing and printing. You do not have to download any PDF files. It is an easy point and click, with several dozens of in-depth plans available for free, all for your viewing pleasure.
You can transfer a graphic on any wood piece of your choice, including a frame, top of a table, etc. The surface should be clean and big enough for the graphic paper. I am also sharing a video tutorial here that explains in detail the process of transferring any graphic to a wooden surface using a freezer paper. Just gather the items you need and follow this video to carve your favorite designs on your favorite wood items.
My second shop (2012) is where I started this whole YouTube and website venture. I was maintenance at an apartment complex which allowed me the opportunity to clean out a junk apartment that was previously used for storage and use it as a shop. At that time the only woodworking tool I had was a Kobalt 10” sliding miter saw from my previous shop. I used it to build my wife’s grandmother a 2×4 sitting bench and the positive feedback from friends and family fueled the fire to get back into woodworking. I took an initial $200 investment from my household income to batch out a bunch of them to sell. That investment and a lot of sweat was the beginning of a snowball that has become my shop.
From the image above it seems that you do not require a big tutorial to help you to build this candle holder. All you need is a wood panel, a hook and some nails/screws and do exactly what you see in the picture. Attach the hook to the wood panel using two screws and then, attach the panel to the wall using more nails or screws. That’s it. I hope this gets the job done.