The next vertical tool is my 13” benchtop drill press. It’s a cheap Harbor Freight model that isn’t perfect but isn’t a bad buy either. It has several flaws that I would consider “areas for improvement” and not problems. I would purchase this again if I had to do it over. I have a larger drill pres table with integrated storage drawers for it but find it to be a little too big for where I currently have the drill press in the shop.
Spanning 14-1/2′ of the back wall is my miter saw station. Completing this has resulted in a huge increase in storage space, organization, and convenience when using the miter saw. It features 20 drawers and a pull out tray for storing my planer out of the way. Eight upper storage bins are for commonly used items such as my cordless tools as well as other items that don’t need to be stored away from dust. There is integrated dust collection for the miter saw and a stop block to the left of the saw with roughly 106” of capacity.
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.

The items you’ll need for this project include wood board, power drill, tape measure, adhesive, etc. Read the tutorial for details. Follow the steps properly to make a nice and strong wall rack. This rack makes use of magnets to hold metal items. The tutorial explains the procedure for building this beautiful wall rack. Make sure to use only high quality items for any woodworking project. Use the rack only to hang items that are not too heavy for the magnet to hold. Also, be careful while working around this wall rack and beware of the knives falling off the rack.
It is one of the easiest woodwork projects we are going to discuss today. Although it looks very easy to make, I still could not find any good tutorial on the internet that explains how to build this one. So I am here sharing an article link that gets the closest. The article explains how to make different kinds of DIY candle holders and what items you may need for the project.
Get perfectly, consistently spaced and centered shelf-pin holes! Economical and practical, this jig can be used on assembled or unassembled cabinetry. Re-designed handle includes two storage compartments for self-centering bits! Ideal for adding shelves to new or existing cabinets. Drills holes either 1-7/16" or 2-1/2" from edge. Insert shelf pin in top or bottom position to extend jig for continuous drilling. Shelving Jigs measure 20" long Additional Self-Centering Bits available. 
Continuing along the left wall is my conduit lumber rack and a dresser I found in the trash several years ago. The dresser stores all of my smaller off-cuts of plywood or lumber that are too small to fit in the plywood cart or the lumber rack. If a piece belongs in these drawers but the drawers are full then it gets thrown away or put in my burn pile near my back yard fire pit.
Below is a list of my top 12 DIY woodworking websites. This list is in no particular order and is by no means meant to be a comprehensive list. There is so much free and paid information available for DIY woodworkers at all skilled levels on the web, it would be impossible to list them all. As always, please support these sites by visiting them, leaving a comment, buying a plan, following them on social media, etc. Please let me know your favorite woodworking websites that I left of the list, enjoy!
And this is the front side which is where I primarily stand when using the table. The top surface has 3/4” holes on 4” centers to allow clamping material pretty much anywhere on the table. It also features a hollow torsion box design for added stiffness to the top surface and empty space just below the work surface to place hand tools out of the way when working on something.
Plywood and long stock can also be a challenge to store in a shop. When I had an 8' bank of cabinets in my shop, I used to slide my sheet goods in behind it. Now that they are gone, I just stand them up against the wall and use a wedge system to keep them neat and upright. Long, narrow material goes on my lumber rack beside my table saw. I also store dry lumber standing on end in one corner of my bench room.
Hey, I want to build all of these (and I did read to the end), but my list of projects is so long that any one of these will have to wait ’til next year (and i don’t mean January). thanks for all these ideas. there is one more i read about in the Handy Family Man. It is an adaptation to your shop vac that puts the hose at your project so it sucks up the dust as it is produced. Wonderful, right? Maybe next year!
Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.

These things may be tiny in size, but building one is not that easy. It takes some serious woodworking knowledge and skill to build a nice wooden mobile stand. When I first saw one online, I just couldn’t resist thinking of buying one. But when I saw the price, I was forced to rethink. Also, a woodwork lover like me cannot be contained with just one piece and I was not willing to spend on more than one. So instead I decided to build myself one. Yes, it took some doing but the final result was satisfying. Luckily, I found this awesome tutorial online that helped me build my first ever wooden phone holder.


The tutorial that I am sharing here was written by someone who built this pallet art just to improve the value of a property they wanted to sell fast and they succeed in it. So you can imagine how wonderful this item must look like. I am assuming you do not just want to make this beautiful pallet art so that you can also sell your property easily. Well, whatever your reasons are, this beauty is able to attract anyone who visits your house.
The procedure is very easy to understand and follow for anyone with a little woodworking knowledge. Make sure to collect all the items you need before you start with the project. You may even ask Tracy your queries directly in the comment section of the tutorial post. Or you can ask them here. Either way, I hope that you manage to build this one nicely.
Their plans are delivered in a PDF format as part of a vlog series. They have regular episodes in the form of “seasons” and “episodes”. Your head will spin with the sheer number of “episodes” on the website. At the time of writing, it is at season 9, episode 933. A small caveat, though, is that you have to subscribe to their newsletter to download the free plans. No biggie. It’s just something to keep in mind.

Google is probably the first place where most people would start searching for woodworking plans, but often the top results can be a mix of articles and how-to pieces that just aren’t detailed enough. Sometimes they’ll link to the plans (like we try to here at Lifehacker), but other times, they’re just showing off a cool project. There are better, more precise ways of finding what you’re looking for.
×