The bandsaw has a 6-3/8” resaw capacity. I find this to be enough for my needs but after recently acquiring some larger chunks of a bradford pear tree that came down in a storm I realized it would be nice to have greater resaw capacity just for getting larger chunks into usable sizes. I don’t think that has justified an upgrade to a larger bandsaw or a riser block kit for me though.
Plywood and long stock can also be a challenge to store in a shop. When I had an 8' bank of cabinets in my shop, I used to slide my sheet goods in behind it. Now that they are gone, I just stand them up against the wall and use a wedge system to keep them neat and upright. Long, narrow material goes on my lumber rack beside my table saw. I also store dry lumber standing on end in one corner of my bench room.
The space behind a door is a storage spot that’s often overlooked. Build a set of shallow shelves and mount it to the wall behind your laundry room door. The materials are inexpensive. Measure the distance between the door hinge and the wall and subtract an inch. This is the maximum depth of the shelves. We used 1x4s for the sides, top and shelves. Screw the sides to the top. Then screw three 1×2 hanging strips to the sides: one top and bottom and one centered. Nail metal shelf standards to the sides. Complete the shelves by nailing a 1×2 trim piece to the sides and top. The 1×2 dresses up the shelf unit and keeps the shelves from falling off the shelf clips.
Who doesn’t want to have one awesome and handy wooden desk organizer that not only looks beautiful but can store all your mini office desk items properly? See the picture below. I am sure you will love this one. I have already built one myself as I just could not resist having one at my office. This thing easily stores all my office desk essentials, including pen, pencils, marker, small notebooks, etc. in the most organized way. You can see it yourself.
Cut off a 21-in.-long board for the shelves, rip it in the middle to make two shelves, and cut 45-degree bevels on the two long front edges with a router or table saw. Bevel the ends of the other board, cut dadoes, which are grooves cut into the wood with a router or a table saw with a dado blade, cross- wise (cut a dado on scrap and test-fit the shelves first!) and cut it into four narrower boards, two at 1-3/8 in. wide and two at 4 in.
And this is the front side which is where I primarily stand when using the table. The top surface has 3/4” holes on 4” centers to allow clamping material pretty much anywhere on the table. It also features a hollow torsion box design for added stiffness to the top surface and empty space just below the work surface to place hand tools out of the way when working on something.
Their plans are delivered in a PDF format as part of a vlog series. They have regular episodes in the form of “seasons” and “episodes”. Your head will spin with the sheer number of “episodes” on the website. At the time of writing, it is at season 9, episode 933. A small caveat, though, is that you have to subscribe to their newsletter to download the free plans. No biggie. It’s just something to keep in mind.
The lower, far left cabinet houses my planer on bottom. Every drawer slide in this miter saw station is a 24” full extension slide except these. To give just a little bit more room when removing the planer for use I opted for 26” full extension slides here. The planer is a DW735 DeWalt planer. When it was in it’s previous setup I gave more info and thoughts on it which can be found here.
The shelf in the first picture is made of red oak plywood. You can choose the wood type, color and design as you like for your project. In case if you need more help understanding this project, you can refer the source link below. It discusses various items used, steps and tips and personal experience of the author who personally built a Zigzag shelf.
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.