The final corner of my shop houses my Grizzly G0703P mobile dust collector. I upgraded to this unit shortly after setting up this shop as my last dust collector was setup to exhaust air outside. The separator I made for it wasn’t efficient enough to modify again for a canister filter for exhausting air inside the shop. I really didn’t want to deal with modifying my dust collector again so I got this. Above the dust collector is my retractable air hose reel that I mentioned earlier. I like having this here as the only times I use compressed air is to fill up the my vehicle tires or to spray a finish which I do outside.
Start with ¾" plywood that is twice as wide as the depth of the cabinet and as long as one side and top/bottom. I crosscut the top and bottom off of one end and set it aside. Then, using a ½" dado stack in my table saw, I cut a series of ¼" deep dadoes across the sides. Make the spacing between them uniform so that the drawers are interchange­able. Finally, rip the sides and top/bottom in half to separate them and assemble the cabinet however you please. If you want to hang it on a wall, attach a French cleat to the back at the top and a batten of equal thickness at the bottom.
Hey, I want to build all of these (and I did read to the end), but my list of projects is so long that any one of these will have to wait ’til next year (and i don’t mean January). thanks for all these ideas. there is one more i read about in the Handy Family Man. It is an adaptation to your shop vac that puts the hose at your project so it sucks up the dust as it is produced. Wonderful, right? Maybe next year!
Drawers are really useful in a wood shop – you can’t have enough. They keep out the dust and with dividers or compart­ments they can help organize as well. A drawer that is too deep ends up getting filled with anything that fits and becomes a junk drawer, so multiple shallow drawers are better than one deep drawer. However, drawer slides can be expensive so I make my own drawers with built-in drawer slides. In addition to saving costs, if I make multiple cabinets the same width, I can move drawers from one cabinet to another quickly and easily.
You can also make one for elders and put it in your garden or terrace or anywhere in the house. Elders can use it to relax and kids can use it to play or sleep. Although this is a really beautiful piece of woodwork, it is not that easy to make. Only someone with good woodworking skill can think of making this swing set. Also, I couldn’t find a good tutorial that illustrates the process of building a wooden boat-shaped swing set. Most Probably, I will write one when I build mine.But if you really want this swing set like right now, I would suggest you hire a good woodworker, who can build something similar. Or just search the internet and maybe you get lucky enough to find a tutorial for this. Good luck either way.
Directly behind my table saw is my 4′ x 8′ modified Paulk workbench that I consider my assembly table as well as an outfeed table. Here’s a shot of the back side of it. I currently have a bunch of 2×10 material on it for an upcoming project and really didn’t want to unload it just for the picture. You can see completed pictures of the project with all of my modifications and changes here.
The miter saw itself is a Ridgid 12” sliding miter saw. I spray painted the handle and motor housing black to match the rest of my tools but didn’t do anything with the insert plate. I plan on making a few down the road so I didn’t bother with painting it. The station has a passive dust collection box around the saw. There is a 4” port at the bottom of the box to create an air draft that pulls the dusty air into the box. The larger chips collect behind the saw wherever they land. My main objective here was to get rid of the dusty air. All of the larger dust can be pushed into the dust port once or twice a year after it builds up.
This is one of those things that you never know you need unless you have one. This amazing wooden sofa sleeve works perfectly on either or both sides of a sofa set. It gives your sofa a nice look. The sleeve can also be modified to include a cup holder, mobile holder, etc. You can easily find this item on any online furniture store, but an even better idea is to build one. This way, you can make a sofa sleeve design that you actually like and make space for cup and other things.
To corral shelf-dwelling books or DVDs that like to wander, cut 3/4-in.-thick hardwood pieces into 6-in. x 6-in. squares. Use a band saw or jigsaw to cut a slot along one edge (with the grain) that’s a smidgen wider than the shelf thickness. Stop the notch 3/4 in. from the other edge. Finish the bookend and slide it on the shelf. Want to build the shelves, too? We’ve got complete plans for great-looking shelves here.

I am sharing here a link to the detailed tutorial written by Pete at diypete.com, who shares the step by step process for making a wonderful barrel coffee table from scratch. He also tells you what items you’ll need for this project and where to find them. For example, you can buy an old whiskey barrel online or from a local whiskey store for a few bucks, if you haven’t already got one.
Building a Wooden Office Desk Organizer is an easy task for a professional woodworker, but not so much for normal people like you and me. But that doesn’t mean you cannot do this. Two years ago, I had almost no woodworking experience, but now I make most of my household and office wooden items by myself. This saves me a lot of money. And believe me when I say this; you can also manage to make wonderful wood items with a little practice and some woodworking experience.
Continuing along the left wall is my conduit lumber rack and a dresser I found in the trash several years ago. The dresser stores all of my smaller off-cuts of plywood or lumber that are too small to fit in the plywood cart or the lumber rack. If a piece belongs in these drawers but the drawers are full then it gets thrown away or put in my burn pile near my back yard fire pit.

Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
An excellent introduction to woodworking is to use crates as your main material. The boxes are already formed, which means less assembly work for you—yet it looks impressive once your project is altogether. With this crate coffee table, you still get to practice your skills adding the casters and the center box. Finish with a little stain, and this table is ready to roll. You can find the full tutorial at DIY Vintage Chic. 
The cost of being disorganized is time. It takes me ten times as long to work on a project when I am scouring the room looking for a drill bit, the right screws, or trying to remember where I last used one of my 10 tape measures. Workshop organization is an ongoing project. As you acquire more tools, you have to rearrange your shop to work in storage for those new items. So mobile and modular storage, wherever possible will save you time down the road. Here are some amazing Workshop Organization Ideas that I hope will inspire you!
The cost of being disorganized is time. It takes me ten times as long to work on a project when I am scouring the room looking for a drill bit, the right screws, or trying to remember where I last used one of my 10 tape measures. Workshop organization is an ongoing project. As you acquire more tools, you have to rearrange your shop to work in storage for those new items. So mobile and modular storage, wherever possible will save you time down the road. Here are some amazing Workshop Organization Ideas that I hope will inspire you!
Can you believe that this amazing wine rack the image below has been built using old wood pallets? Perhaps you can. Isn’t it wonderful that your old wood pallets can be reused to build something so beautiful and useful? I am not a drinker but I liked the idea so much that I just couldn’t resist making myself one. Although later I gifted it to my parents, who totally loved it.

This is probably one the easiest woodworking projects you will find here. Although easy, a doormat is an equally important and useful item for households. As you can see in the image below, you will only need some 2X2 wooden boards and rope to build a simple doormat. This doormat is mostly useful for outdoor and porch. It will easily remove all the mud from your shoes with just one wipe. It is also very easy to clean and looks fabulous even if it is dirty.

By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking.   These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email orderdesk@canadianwoodworking.com  and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence. 
We cut the supports 16 in. long, but you can place the second shelf at whatever height you like. Screw the end supports to the walls at each end. Use drywall anchors if you can’t hit a stud. Then mark the position of the middle supports onto the top and bottom shelves with a square and drill 5/32-in. clearance holes through the shelves. Drive 1-5/8-in. screws through the shelf into the supports. You can apply this same concept to garage storage. See how to build double-decker garage storage shelves here.
Their free woodworking plans are well-illustrated, easy to follow and best of all – free. You can’t beat that! Their plans are directly available on their website for easy viewing and printing. You do not have to download any PDF files. It is an easy point and click, with several dozens of in-depth plans available for free, all for your viewing pleasure.
×