The source above is not exactly a tutorial, but it gives you a basic idea of how the author built a Quirky Pallet Art to enhance the look of their old house. You can also find another tutorial at the link below. It shares a step by step procedure for making a wooden pallet sign. The final product is not exactly the same as the one above, but the basic idea is the same.

The final corner of my shop houses my Grizzly G0703P mobile dust collector. I upgraded to this unit shortly after setting up this shop as my last dust collector was setup to exhaust air outside. The separator I made for it wasn’t efficient enough to modify again for a canister filter for exhausting air inside the shop. I really didn’t want to deal with modifying my dust collector again so I got this. Above the dust collector is my retractable air hose reel that I mentioned earlier. I like having this here as the only times I use compressed air is to fill up the my vehicle tires or to spray a finish which I do outside.
Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.
This rack can be built from old unused wood pallets you can find around the house. So it is also a great way to recycle those old pallets. You can also find a step by step tutorial at instructables.com for which I have included the source link below. This tutorial helps you to make a wood wine rack from the scratch. So what are waiting for? Just grab the items you need and start building a cool wooden rack for those nice wine bottles of yours.
No doubt many of us would love to have a huge, 2000 square foot building devoted to woodcraft, on a wooded acreage somewhere. But there is a reality that goes with a hobby shared by numerous ordinary people: very few really have the means to set up such palatial workshops. We have our lives to lead, and engaging in such a venture is out of the reach for most, myself included. This article is dedicated to workshops for "the rest of us."
Above my miter saw station along the entire length of the back wall minus the area needed to get into my attic are wasted space garage storage shelves. This is where I throw any household items that don’t have a place in the house and I don’t want taking up space in my shop. I also store empty boxes up there for future shipping purposes as needed. This project was a duplicate of what I made above the garage door shortly after moving into the house.
Another wooden item that I love very much is a beautiful mobile holder. You can see one in the image below. These things are not only beautiful, but they can comfortably hold any sized mobile and ensure proper safety. Another amazing thing is that they can be built in many shapes and sizes, as and how you need it. You can see some more examples at the source below
To the left of the welder is the door into my house and to the left of that is the community sticker cabinet. About six months ago I wanted to start a sticker collage and asked people on my vlog channel if any of them had sticker for their business for sale. Since then I’ve only purchased about six of the stickers on the cabinet and the rest of them have been provided by all of you out there. So basically this is a community sticker collage. It grows every week. It’s a locking metal cabinet that is about 6-1/2′ tall, 18” deep, and 36” wide.
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.
To corral shelf-dwelling books or DVDs that like to wander, cut 3/4-in.-thick hardwood pieces into 6-in. x 6-in. squares. Use a band saw or jigsaw to cut a slot along one edge (with the grain) that’s a smidgen wider than the shelf thickness. Stop the notch 3/4 in. from the other edge. Finish the bookend and slide it on the shelf. Want to build the shelves, too? We’ve got complete plans for great-looking shelves here.

Their free woodworking plans are well-illustrated, easy to follow and best of all – free. You can’t beat that! Their plans are directly available on their website for easy viewing and printing. You do not have to download any PDF files. It is an easy point and click, with several dozens of in-depth plans available for free, all for your viewing pleasure.

Slice, dice and serve in style on this easy, attractive board. We’ll show you a simple way to dry-fit the parts, scribe the arc and then glue the whole thing together. We used a 4-ft. steel ruler to scribe the arcs, but a yardstick or any thin board would also work. Find complete how-to instructions on this woodworking crafts project here. Also, be sure to use water-resistant wood glue and keep your board out of the dishwasher or it might fall apart. And one more thing: Keep the boards as even as possible during glue-up to minimize sanding later. For great tips on gluing wood, check out this collection.


To my right, I have my sharpening bench, drill press and charging station. The sharpening bench is equipped with a 6" metal vise and houses all my sharpening accessories. On the back of the bench is a fluorescent lamp with a magnify­ing lens that is shared with the drill press. All my drill bits are stored either in the drawer beneath the drill press table or in boxes hung on French cleats. To the right of the drill press, I have a shelf with a power bar that supplies power to my bat­tery chargers. I leave them all plugged in and instead use the power bar’s on/off rocker switch.


The cost of being disorganized is time. It takes me ten times as long to work on a project when I am scouring the room looking for a drill bit, the right screws, or trying to remember where I last used one of my 10 tape measures. Workshop organization is an ongoing project. As you acquire more tools, you have to rearrange your shop to work in storage for those new items. So mobile and modular storage, wherever possible will save you time down the road. Here are some amazing Workshop Organization Ideas that I hope will inspire you!

Wall-mounted or placed on a table or countertop, this handsome display cabinet is the perfect way to share any collection while keeping it clean and protected at the same time. Featuring tempered glass doors and three shelves, the cabinet’s design calls for all straight cuts and straightforward construction techniques (simple cut-outs give the effect of
Continuing along the left wall is my conduit lumber rack and a dresser I found in the trash several years ago. The dresser stores all of my smaller off-cuts of plywood or lumber that are too small to fit in the plywood cart or the lumber rack. If a piece belongs in these drawers but the drawers are full then it gets thrown away or put in my burn pile near my back yard fire pit.
Directly behind my table saw is my 4′ x 8′ modified Paulk workbench that I consider my assembly table as well as an outfeed table. Here’s a shot of the back side of it. I currently have a bunch of 2×10 material on it for an upcoming project and really didn’t want to unload it just for the picture. You can see completed pictures of the project with all of my modifications and changes here.
The next vertical tool is my 13” benchtop drill press. It’s a cheap Harbor Freight model that isn’t perfect but isn’t a bad buy either. It has several flaws that I would consider “areas for improvement” and not problems. I would purchase this again if I had to do it over. I have a larger drill pres table with integrated storage drawers for it but find it to be a little too big for where I currently have the drill press in the shop.
A small oak table is a very useful wooden item for every household. You can yourself make a nice, strong and beautiful oak table suitable for any purpose. See the image below. As you can see, it is a small, yet good enough table to be used as a coffee table, lamp stand, breakfast table, etc. You can also find many other design variants on the internet. Choose the one you want for yourself and start making it now.
Plywood and long stock can also be a challenge to store in a shop. When I had an 8' bank of cabinets in my shop, I used to slide my sheet goods in behind it. Now that they are gone, I just stand them up against the wall and use a wedge system to keep them neat and upright. Long, narrow material goes on my lumber rack beside my table saw. I also store dry lumber standing on end in one corner of my bench room.
My first woodworking “shop” was in the living room and kitchen of a run-down house trailer (2008-ish). Nothing pretty at all but it was functional. At that time I was living on my own with a job paying just over minimum wage. The engine in my truck blew a head gasket and the only option for me to rebuild the engine without going into debt was to sell off my woodshop. I sold everything but my miter saw. It was a hard lesson learned on being prepared with an emergency fund and I’ll never put myself in that kind of situation again.
My second shop (2012) is where I started this whole YouTube and website venture. I was maintenance at an apartment complex which allowed me the opportunity to clean out a junk apartment that was previously used for storage and use it as a shop. At that time the only woodworking tool I had was a Kobalt 10” sliding miter saw from my previous shop. I used it to build my wife’s grandmother a 2×4 sitting bench and the positive feedback from friends and family fueled the fire to get back into woodworking. I took an initial $200 investment from my household income to batch out a bunch of them to sell. That investment and a lot of sweat was the beginning of a snowball that has become my shop.
Continuing along the left wall is my conduit lumber rack and a dresser I found in the trash several years ago. The dresser stores all of my smaller off-cuts of plywood or lumber that are too small to fit in the plywood cart or the lumber rack. If a piece belongs in these drawers but the drawers are full then it gets thrown away or put in my burn pile near my back yard fire pit.
The items you’ll need for this project include wood board, power drill, tape measure, adhesive, etc. Read the tutorial for details. Follow the steps properly to make a nice and strong wall rack. This rack makes use of magnets to hold metal items. The tutorial explains the procedure for building this beautiful wall rack. Make sure to use only high quality items for any woodworking project. Use the rack only to hang items that are not too heavy for the magnet to hold. Also, be careful while working around this wall rack and beware of the knives falling off the rack.
My second shop (2012) is where I started this whole YouTube and website venture. I was maintenance at an apartment complex which allowed me the opportunity to clean out a junk apartment that was previously used for storage and use it as a shop. At that time the only woodworking tool I had was a Kobalt 10” sliding miter saw from my previous shop. I used it to build my wife’s grandmother a 2×4 sitting bench and the positive feedback from friends and family fueled the fire to get back into woodworking. I took an initial $200 investment from my household income to batch out a bunch of them to sell. That investment and a lot of sweat was the beginning of a snowball that has become my shop.
Jay, You gave some vital advise- not to go into debt over a tool. Unfortunately I do owe a little for some of my things about $300.00 worth, but I went from $60,000/year income down to $25,000/year when I retired due to bone CA I had as a teen.( I was only suppose to live 3 month and I am now 54, so guess they were wrong about that.) But with age comes arthritis in the arek9a of surgery and was force to give up my job as a mail carrier. The income drop was and is huge for me. I have paid cash for 90% of my tools, but some i have had to charge. I really only need one more tool which is a Thickness planer. I’m holding out for a sale on the Rigid Planer which has all the features I want. Enough about me. I have watched your shop grow from the first video to this video and it has come out beautifully and a model for others to follow, especially your Miter station. Anyone with that amount of space could easily make it with your plans,or just watching the build video’s. You have utilized every inch of that garage perfectly, and I love the idea of having a rolling storage rack for sheet goods that can be moved to you truck to unload and move back into place. You have come along way in a years time. Maybe I should start making bigger item and sell them out front on my lawn, instead of on Etsy. Best of luck always Jay. PS.- I’m wearing your shirt that say’s” Nothing works unless you do”. It’s my motto now.~Dolly
Right in front of my finishing supply rack is my welder and welder cabinet. It’s a Hobart Handler 140 mig or flux core wire feed welder. I learned how to weld several years ago on an old manual adjustment arc welder and I very much like the convenience of the wire feed in this one. It’s sitting on a Harbor Freight welding cabinet. I have only used it in one video so far (metal vise build) but have used it a few times since then on stuff around the house. Having a welder isn’t a necessity but it is very convenient at times.
As with many of you out there I always enjoy checking out a shop tour. I hope you were able to take away at least something from this shop tour. If you would like to see some reader shop tours that have already been featured on this website you can do so here. If you would like your shop to be featured on this website feel free to drop me a line using my contact form. Thanks for stopping by folks and have a great day!
I got this idea from a Pinterest post. The final product looks so beautiful that I just couldn’t wait to make one for myself. This was somewhat a different experience from my other regular DIY projects as it doesn’t involve making something from scratch, but turning an existing wood piece into another one. Nonetheless, I enjoyed it very much and the final product was very satisfying. The tutorial I used is linked below.

I recently met  a man  known among local woodworkers for having a large workshop with a lot of tools. He offered to show me his workshop, and  take photographs of it. His workshop covers the entire basement of a large 1800 square foot bungalow. It's difficult to capture this workshop in just a few photos, so I figured I'd include a large number of photos.


Day in and day out we all deal with electricity, but it seems to be some illusive concept that few woodworkers really understand. Electricity drives our tools, and drives our everyday life. Electricity has the versatility to replace many older forms of energy. Without it we would still be using lanterns for light, fires for heat, and oxen for work.
It’s been a solid year since moving into this house and starting my shop. Nearly everything in my shop is on casters for mobility. In my opinion the most important tool in any woodshop is the table saw so lets start there. My table saw is a SawStop PCS with 52” rip capacity. The attention to detail on this machine is phenomenal. I have the industrial mobile base for it which makes the single heaviest item in my shop one of the easiest to move. The base lifts the entire saw, including the extension wing, several inches with ease. It is actually in the up position in the following image. I also spray painted the location of the extension wing supports on the ground so I can easily locate a familiar position when setting up the saw. Because moving it around the shop on the mobile base is effortless I find myself moving it out of the way frequently when I know I’m not going to be using it for a while. I also keep a couple trash cans near the table saw.

This Privacy Policy covers CanadianWoodworking.com's treatment of personally identifiable information that CanadianWoodworking.com collects when you are on the CanadianWoodworking.com site, and when you use CanadianWoodworking.com's services. This policy also covers CanadianWoodworking.com's treatment of any personally identifiable information that CanadianWoodworking.com's business partners share with CanadianWoodworking.com.
×