Build this handy stool in one hour and park it in your closet. You can also use it as a step to reach the high shelf. All you need is a 4 x 4-ft. sheet of 3/4-in. plywood, wood glue and a handful of 8d finish nails. Cut the plywood pieces according to the illustration. Spread wood glue on the joints, then nail them together with 8d finish nails. First nail through the sides into the back. Then nail through the top into the sides and back. Finally, mark the location of the two shelves and nail through the sides into the shelves. Don’t have floor space to spare? Build these super simple wall-mounted shoe organizers instead!

Directly behind my table saw is my 4′ x 8′ modified Paulk workbench that I consider my assembly table as well as an outfeed table. Here’s a shot of the back side of it. I currently have a bunch of 2×10 material on it for an upcoming project and really didn’t want to unload it just for the picture. You can see completed pictures of the project with all of my modifications and changes here.


Some tools required for this project are hole saw, drilling machine, pencil, tape measure, clamps, etc. This tutorial explains every step properly with images so that anyone can make a wooden sofa sleeve easily. Those, who prefer a video tutorial, can visit the below link to a YouTube video that illustrates the process of building a DIY Sofa Sleeve Cupholder.

Get perfectly, consistently spaced and centered shelf-pin holes! Economical and practical, this jig can be used on assembled or unassembled cabinetry. Re-designed handle includes two storage compartments for self-centering bits! Ideal for adding shelves to new or existing cabinets. Drills holes either 1-7/16" or 2-1/2" from edge. Insert shelf pin in top or bottom position to extend jig for continuous drilling. Shelving Jigs measure 20" long Additional Self-Centering Bits available. 
So that takes care of the center of my shop. I’ll work my way around the perimeter starting at the right wall and moving left. The first item is my rolling plywood cart. I built this a few weeks ago to replace my unsuccessful stationary plywood rack. It’s an 8′ plywood cart that stores full sheets of plywood on one side and off-cuts on the other side. Because it’s on casters I can easily push it outside next to my truck to load it up and also push the entire cart behind the table saw to reduce the distance I need to carry full sheets to be cut down. It’s the design in issue 205 of Wood Magazine.
Plywood and long stock can also be a challenge to store in a shop. When I had an 8' bank of cabinets in my shop, I used to slide my sheet goods in behind it. Now that they are gone, I just stand them up against the wall and use a wedge system to keep them neat and upright. Long, narrow material goes on my lumber rack beside my table saw. I also store dry lumber standing on end in one corner of my bench room.

Here, I am writing about another DIY project that involves the use of an old furniture piece. I think that the idea of reusing and recycling old furniture has got to me. Anyways, I am starting to love it. This project involves using an old door to build a beautiful multi picture frame, as you can see in the image below. This frame looks really wonderful and can be used to hold many pictures at a time.


For your kitchen, it can work as a knife rack. It gives you easy access to all essential tools while saving space. In addition, it adds a nice visual appeal to your kitchen wall. You can customize your wall rack with different materials, designs and styles. I am here sharing the source link to the step by step tutorial about how to make a rustic wall knife rack.
Plywood and long stock can also be a challenge to store in a shop. When I had an 8' bank of cabinets in my shop, I used to slide my sheet goods in behind it. Now that they are gone, I just stand them up against the wall and use a wedge system to keep them neat and upright. Long, narrow material goes on my lumber rack beside my table saw. I also store dry lumber standing on end in one corner of my bench room.
Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.

Wall-mounted or placed on a table or countertop, this handsome display cabinet is the perfect way to share any collection while keeping it clean and protected at the same time. Featuring tempered glass doors and three shelves, the cabinet’s design calls for all straight cuts and straightforward construction techniques (simple cut-outs give the effect of
The tutorial that I am sharing here was written by someone who built this pallet art just to improve the value of a property they wanted to sell fast and they succeed in it. So you can imagine how wonderful this item must look like. I am assuming you do not just want to make this beautiful pallet art so that you can also sell your property easily. Well, whatever your reasons are, this beauty is able to attract anyone who visits your house.
Above my miter saw station along the entire length of the back wall minus the area needed to get into my attic are wasted space garage storage shelves. This is where I throw any household items that don’t have a place in the house and I don’t want taking up space in my shop. I also store empty boxes up there for future shipping purposes as needed. This project was a duplicate of what I made above the garage door shortly after moving into the house.
You can also make one for elders and put it in your garden or terrace or anywhere in the house. Elders can use it to relax and kids can use it to play or sleep. Although this is a really beautiful piece of woodwork, it is not that easy to make. Only someone with good woodworking skill can think of making this swing set. Also, I couldn’t find a good tutorial that illustrates the process of building a wooden boat-shaped swing set. Most Probably, I will write one when I build mine.But if you really want this swing set like right now, I would suggest you hire a good woodworker, who can build something similar. Or just search the internet and maybe you get lucky enough to find a tutorial for this. Good luck either way.
Google is probably the first place where most people would start searching for woodworking plans, but often the top results can be a mix of articles and how-to pieces that just aren’t detailed enough. Sometimes they’ll link to the plans (like we try to here at Lifehacker), but other times, they’re just showing off a cool project. There are better, more precise ways of finding what you’re looking for.
×