To my right, I have my sharpening bench, drill press and charging station. The sharpening bench is equipped with a 6" metal vise and houses all my sharpening accessories. On the back of the bench is a fluorescent lamp with a magnify­ing lens that is shared with the drill press. All my drill bits are stored either in the drawer beneath the drill press table or in boxes hung on French cleats. To the right of the drill press, I have a shelf with a power bar that supplies power to my bat­tery chargers. I leave them all plugged in and instead use the power bar’s on/off rocker switch.
Although refrigerators long ago rendered them obsolete, antique oak ice boxes remain popular with collectors, even though they’re expensive and hard to find. This do-it-yourself version is neither: it’s both inexpensive and easy to build. An authentic reproduction of an original, the project is especially popular when used as a bar, but it has many
Right in front of my finishing supply rack is my welder and welder cabinet. It’s a Hobart Handler 140 mig or flux core wire feed welder. I learned how to weld several years ago on an old manual adjustment arc welder and I very much like the convenience of the wire feed in this one. It’s sitting on a Harbor Freight welding cabinet. I have only used it in one video so far (metal vise build) but have used it a few times since then on stuff around the house. Having a welder isn’t a necessity but it is very convenient at times.
It’s been a solid year since moving into this house and starting my shop. Nearly everything in my shop is on casters for mobility. In my opinion the most important tool in any woodshop is the table saw so lets start there. My table saw is a SawStop PCS with 52” rip capacity. The attention to detail on this machine is phenomenal. I have the industrial mobile base for it which makes the single heaviest item in my shop one of the easiest to move. The base lifts the entire saw, including the extension wing, several inches with ease. It is actually in the up position in the following image. I also spray painted the location of the extension wing supports on the ground so I can easily locate a familiar position when setting up the saw. Because moving it around the shop on the mobile base is effortless I find myself moving it out of the way frequently when I know I’m not going to be using it for a while. I also keep a couple trash cans near the table saw.
By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking.   These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email orderdesk@canadianwoodworking.com  and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence. 
I recently met  a man  known among local woodworkers for having a large workshop with a lot of tools. He offered to show me his workshop, and  take photographs of it. His workshop covers the entire basement of a large 1800 square foot bungalow. It's difficult to capture this workshop in just a few photos, so I figured I'd include a large number of photos.
Once you get your shop organized, you’ll fully realize just how nice it is to be able to find and access things easily as well as have room to work! You'll soon find yourself actually putting tools back where they belong when you are done with them. Whether the shop is where you spend weekdays or weekends, you’ll really appreciate an organized shop.

Here, I am writing about another DIY project that involves the use of an old furniture piece. I think that the idea of reusing and recycling old furniture has got to me. Anyways, I am starting to love it. This project involves using an old door to build a beautiful multi picture frame, as you can see in the image below. This frame looks really wonderful and can be used to hold many pictures at a time.
Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience. 

Fast forward two and a half years since the start of shop #2. My wife finished college and my online business was at a sustainable point for me to leave my day job which lead us to house shopping. We ended up getting our first house together on July 2nd 2014. The house we found fit literally every one of our criteria including the most important for me which was a two car garage. With an empty garage to start my current shop I gave the walls a fresh coat of white paint and ran new electrical wires for the shop inside a long box along the bottom of the left and rear walls.
By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.
A bottle carrier is a bucket like carrier used to carry beer bottles and so. Yes, the same one you must have used to carry your six-pack. Drinker or not, a bottle carrier is a useful item for everyone. It can be used to carry around or store small items around a household. And it is also very easy to build one. I have several of these lying around my house. Also known as wooden beer totes, this is one wood item you will absolutely love to make. It is also super easy to build.

Build this handy stool in one hour and park it in your closet. You can also use it as a step to reach the high shelf. All you need is a 4 x 4-ft. sheet of 3/4-in. plywood, wood glue and a handful of 8d finish nails. Cut the plywood pieces according to the illustration. Spread wood glue on the joints, then nail them together with 8d finish nails. First nail through the sides into the back. Then nail through the top into the sides and back. Finally, mark the location of the two shelves and nail through the sides into the shelves. Don’t have floor space to spare? Build these super simple wall-mounted shoe organizers instead!


So that takes care of the center of my shop. I’ll work my way around the perimeter starting at the right wall and moving left. The first item is my rolling plywood cart. I built this a few weeks ago to replace my unsuccessful stationary plywood rack. It’s an 8′ plywood cart that stores full sheets of plywood on one side and off-cuts on the other side. Because it’s on casters I can easily push it outside next to my truck to load it up and also push the entire cart behind the table saw to reduce the distance I need to carry full sheets to be cut down. It’s the design in issue 205 of Wood Magazine.
Lumber and supplies are moved in and out of the shop through the front overhead door. To the left of the door are the lumber and plywood storage racks. Across from the lumber rack and to the right of the overhead door is the radial arm saw, miter saw and mortise utilizing a single fence system for all operations. Below and above these are cabinets and storage for misc. power hand tools. Next to the radial arm saw and in the corner is the floor drill press with accessory storage next to it for all drilling operations.  Across from the radial arm saw is a separate workstation set up with a small portable table saw and router set-up with storage underneath for routers, bits and accessories.

Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.


Wall-mounted or placed on a table or countertop, this handsome display cabinet is the perfect way to share any collection while keeping it clean and protected at the same time. Featuring tempered glass doors and three shelves, the cabinet’s design calls for all straight cuts and straightforward construction techniques (simple cut-outs give the effect of
Their plans are delivered in a PDF format as part of a vlog series. They have regular episodes in the form of “seasons” and “episodes”. Your head will spin with the sheer number of “episodes” on the website. At the time of writing, it is at season 9, episode 933. A small caveat, though, is that you have to subscribe to their newsletter to download the free plans. No biggie. It’s just something to keep in mind.
A small oak table is a very useful wooden item for every household. You can yourself make a nice, strong and beautiful oak table suitable for any purpose. See the image below. As you can see, it is a small, yet good enough table to be used as a coffee table, lamp stand, breakfast table, etc. You can also find many other design variants on the internet. Choose the one you want for yourself and start making it now.
I really enjoyed this video. I don’t particularly enjoy watching videos every time someone changes the layout of their shop. But, yours is the exception. I know a lot of your fans have probably been asking for a while for you to do a tour of your shop. Glad you waited till it was all finished to do it. You must’ve shot this video before you got your festool tools.
The space behind a door is a storage spot that’s often overlooked. Build a set of shallow shelves and mount it to the wall behind your laundry room door. The materials are inexpensive. Measure the distance between the door hinge and the wall and subtract an inch. This is the maximum depth of the shelves. We used 1x4s for the sides, top and shelves. Screw the sides to the top. Then screw three 1×2 hanging strips to the sides: one top and bottom and one centered. Nail metal shelf standards to the sides. Complete the shelves by nailing a 1×2 trim piece to the sides and top. The 1×2 dresses up the shelf unit and keeps the shelves from falling off the shelf clips.

Working on wood based on wood plans is great fun. However, many times, the enthusiastic beginner is faced with so-called woodworker-block. On what to work, exactly? Indeed, it can be quite difficult to start a project without the proper guideline. We scoured the web in search of good websites that offer free woodworking plans for beginners. They are excellent guidelines to help you work on a project from start to finish.
×